Manual Parkside IAN 86735 PASS 3.6 A1 (page 56 of 62) (English, German, Dutch, French)

745079

Zoom out

Zoom in

1/62

- 56 -

7.5 Handle adjustment (Fig. 3/Item 3)

The screwdriver can be locked into 2 different

angle settings. To do so, press the locking button

(3) and move the screwdriver into the desired po-

sition. Then release the locking button (3).

 Caution:

Before you switch on the screwdriver, make sure

that it is correctly locked in the required angle

position.

7.6 Battery capacity indicator

(Fig. 4/Item. 5)

Press the button for the battery capacity indicator

(6). The battery capacity indicator (5) indicates

the charge state of the battery on 3 coloured

LEDs.

All LEDs are lit:

The battery is fully charged.

The yellow and red LED illuminate:

The battery has an adequate remaining charge.

Red LED:

The battery is discharged, it requires charging.

7.7 Changing the tool (Fig. 5)

 Important.

Set the clockwise/counter-clockwise changeover

switch (10) to its centre position whenever you

carry out any work (for example changing the

tool, maintenance work, etc.) on the cordless

screwdriver.

•

Pull back and hold the locking sleeve (14).

•

Insert the bit (a) into the bit chuck (1) and let

go of the locking sleeve (14)

•

Check that it is properly secure by pulling the

tool.

•

For removal of bits (a), pull back the locking

sleeve (14) and hold it firmly.

•

Remove the bit (a) and let go of the locking

sleeve.

7.8 Torque Setting (Fig. 5/Item 13)

 Caution:

Only adjust the torque when the appliance is at a

standstill.

The cordless screwdriver is ﬁ tted with a mechani-

cal torque selector.

The torque for each particular screw size is ad-

justable at the torque selector (13). The required

torque is dependent upon several factors:

•

the type and hardness of the material to be

worked with.

•

the type and length of the screws used.

•

the physical burden placed on the screw con-

nection.

When the torque is reached, this is indicated by

the clutch being released.

7.9 Screws

It is advisable to use self-centering screws (e.g.

Torx, Philips head screws) as these will enable

you to work safely and reliably. Always make sure

that the bit used is of the same size and shape as

the screw.

7.10 Screwdriver overloaded

If the screwdriver is overloaded, the automatic

safety switch turns the device off. After a few se-

conds the screwdriver can be used again.

Anl_4513422.indb 56Anl_4513422.indb 56 25.10.12 18:3325.10.12 18:33

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 86735 PASS 3.6 A1 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 86735 PASS 3.6 A1 Manual

Product: