745079

Parkside IAN 86735 PASS 3.6 A1 Manual

55
Zoom out
Zoom in
Previous page
1/62
Next page
GB
- 55 -
6. Before starting the
equipment
Caution:
Be sure to read the following information before
you use your cordless screwdriver for the fi rst time:
1. Only charge the battery pack using the char-
ger (11) supplied.
2. Only use screwdriver bits which are in perfect
working order and appropriate.
3. When screwing into walls or partitions, test
these for electrical, gas or water connections.
7. Operation
7.1 Charging the battery pack (Fig. 1)
The battery pack is protected from exhaustive di-
scharge. An integrated protective circuit automati-
cally switches off the equipment when the battery
pack is fl at. In this case the bit chuck (1) will cease
to turn.
Caution:
Do not press the ON/OFF switch (9) any more,
if the protective circuit has actuated. This may da-
mage the battery pack.
1. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Plug the battery charger (11) in the
plug socket and connect the charging cable
(12) to the charging connection (8). The char-
ging process starts as soon as the charging
cable is connected to the charging connec-
tion.
2. The charging control lamp (7) indicates that
the battery is being charged.
3. The charging control lamp (7) goes out when
charging is completed.
Caution:
The handle may become a little warm during the
charging process. This is normal.
If the battery pack fails to charge, please check
•
whether there is voltage at the socket-outlet.
•
whether there is good contact at the charging
contacts of the battery charger (11).
If the battery still fails to charge, send
•
the battery charger (11)
•
and the screwdriver
to our customer services department.
Timely recharging of the battery pack will help to
prolong its lifespan. You must recharge the bat-
tery pack when you notice that the power of the
screwdriver drops.
7.2 Clockwise/Counter-clockwise chan-
geover switch (Fig. 2/Item 10)
The clockwise/counter-clockwise changeover
switch (10) above the ON/OFF switch (9) is
for setting the direction of rotation of the cord-
less screwdriver and for preventing the cordless
screwdriver from being switched on inadvertently.
You can select between clockwise and counter-
clockwise rotation.
Important.
Change the direction of rotation only when the
equipment is at a standstill. If you fail to observe
this point, the gearing may become damaged.
When the clockwise/counter-clockwise changeo-
ver switch (10) is in the middle position, the ON/
OFF switch (9) is blocked.
Direction Switch position
Clockwise “R” pressed
Counter-clockwise “L” pressed
7.3 ON/OFF switch (Fig. 2/Item 9)
Press the ON/OFF switch (9) to switch the cord-
less screwdriver on. Release the ON/OFF switch
to switch off the tool.
7.4 LED lamp (Fig. 2/Item 2)
The LED lamp (2) can be used in poor lighting
conditions to illuminate the area where you want
to screw. To switch ON, press the switch (4) and
to switch OFF, press the switch (4) again.
Anl_4513422.indb 55Anl_4513422.indb 55 25.10.12 18:3325.10.12 18:33
… 55 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 86735 PASS 3.6 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 86735 PASS 3.6 A1 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info