744938
33
Zoom out
Zoom in
Previous page
1/45
Next page
33 GB/MT
out the mains plug. This prevents the grinder restar
t-
ing by accident, which could cause injury to you.
Never operate the grinder if the power
cable or mains plug is damaged.
Grinding stones must be carefully
stored and handled according to the
manufacturer’s instructions.
Make sure that the grinding tools are
appropriate in line with the instructions
of the manufacturer.
Check the grinding stone before using
it; do not use any broken, cracked or otherwise
damaged goods.
Make sure that a grinding tool is correct-
ly fitted and fastened before using it.
Place the grinder in a safe place and allow it
to run idly for 30 seconds. Stop it immediately if
considerable oscillations occur or if defects are
observed. If this occurs, check the machine to
find out the cause.
Original accessories /
Attachments
Use only the accessories and attachments
detailed in the operating instructions.
The use of inserted tools or accessories other
than those recommended in the operating in-
structions could lead to you suffering an injury.
Use
Sharpening a drill
NOTE: Badly damaged drills should first be coarsely
sharpened on a sharpening block.
Fully lower the sharpening stone. To do this turn
the rotary switch
1
in the DOWN direction
as far as it will go.
Insert the drill into the smallest suitable drill
guide
11
on the drill sharpener. The exact size
(Ø) of each drill guide
11
is shown by the ad-
jacent lettering (3 to 10).
Press the ON / OFF switch
4
into position “I”
to switch on the device.
Turn the rotary switch
1
in the UP direction
until you hear a grinding noise.
NOTE: The rotary switch
1
controls the posi-
tion of the sharpening stone in the sharpening
head housing and therefore the pressure of the
sharpening stone against the drill. The further
you turn the rotary switch
1
in the UP di-
rection, the greater the pressure. Ensure that
you do not turn the sharpening stone too far up.
Otherwise the sharpening stone could strike
the housing.
Turn the drill under slight pressure loosely and
quickly to and fro between the left and right
stops about 10 times (with small drills about
5 times).
Pull the drill out, turn it through 180° (horizon
tally)
and insert it again until it meets the sharpening
stone.
If necessary repeat whole process until both
cutting edges of the drill are sharp. Control the
grinding operation so that the angle between
the main and transverse cutting edges for a
standard drill is 130°. Both cutting edges (b)
must have the same angle to the drill axis (a)
and be the same length so that the drill runs
concentrically (see following figures).
(b)(b)
(a)
Press the ON / OFF switch
4
into position “0”
to switch off the device.
Replacing the
sharpening stone
RISK OF INJURY! Before you
carry out any work on the device, always pull the
mains plug out of the mains socket. Replace the
sharpening stone if it is worn out or damaged
(deteriorating, irregular sharpening performance,
General safety advice / Use
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 61094 PBSG 55 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 61094 PBSG 55 A1 in the language / languages: English, Portuguese, Spanish as an attachment in your email.

The manual is 1,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 61094 PBSG 55 A1

Parkside IAN 61094 PBSG 55 A1 User Manual - German, Dutch, French, Italian - 37 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info