Manual Parkside IAN 315808 PHS 9500 A1 (page 29 of 100) (English, German, Dutch, French, Polish)

749330

Zoom out

Zoom in

1/100

25GB/IE

• Make sure that the ON/OFF switch (6), the throttle lock-out

switch (7) and the throttle trigger (9) function perfectly.

• This hedge trimmer is only allowed to be started after it is

completely assembled.

• Support the hedge trimmer when starting and hold it ﬁrmly.

Make sure that the cutting device can move freely.

10.1 Use (Fig. 1, 3, 4):

10.1.1 Starting when the engine is cold

Never allow the ranking rope (5) to whip back. This could

cause damage.

1. Remove the knives protection (F) from the cutting device

(1).

2. Place the hedge trimmer on a ﬁrm, level surface. The cut-

ting device (1) must not touch the ground.

3. Press the fuel pump “Primer“ (12) 6 times.

4. Switch the On/Oﬀ switch (6) to “I”.

5. Turn the choke (4) to „cold start“ .

6. Place the tip of your shoe into the rear handle (8)

7. Hold the hedge trimmer ﬁrmly by the front handle (3) and

pull the cranking rope (5) slowly until you feel resistance.

8. Now pull the cranking rope (5) quickly so that the engine

starts. If the engine does not start, repeat the process. As

long as the choke (4) is on „cold start“ , the engine

will only run for a short time and then switch oﬀ.

9. As soon as the engine is oﬀ, press the throttle lock-out

switch (7) and the throttle trigger (9) simultaneously. The

choke automatically jumps to the “warm start” operat-

ing position.“

10. Now pull the cranking rope (5) quickly again so that the

engine starts.

If the engine does not start after several attempts, read the

“15.Troubleshooting”.

Caution

Always pull the cranking rope (5) straight out. Hold the handle

of the cranking rope (5) ﬁrmly when the cranking rope (5) re-

tracts. Do not allow the cranking rope (5) to whip back.

Note:

At very high outdoor temperatures it is possible that even a cold

engine has to be started without using the choke!

Note:

If the cutting device (1) moves when it is idling or the engine

goes out when you release the throttle, you need to adjust the

carburettor (see section “12.2 Adjusting the idle speed”).

11. Lift the hedge trimmer.

12. Hold the front handle (3) ﬁrmly in your left hand.

13. Hold the rear handle (8) irmly in your right hand. The ball

of your hand now lies on the throttle lock-out switch (7)

and your index ﬁnger operates the throttle trigger (9).

14. After pulling the throttle trigger (9), once, the engine

should idle.

15. Run the engine to warm it up.

10.1.2 Starting with warm engine

1. Switch the On/Oﬀ switch (6) to „I“.

2. The Choke must be set to „warm start“ to start the

warm engine.

3. Place the tip of your shoe into the rear handle (8).

4. Hold the hedge trimmer by the front handle (3) and pull

the cranking rope (5) slowly until you feel resistance.

5. Now pull the cranking rope (5) quickly. The appliance

should start after 1–2 pulls. If the appliance still hasn’t

started after 6 pulls, repeat the process as described in

“10.1.1 Starting when the engine is cold”.

10.2 Stopping the engine

10.2.1 Emergency stop sequence

If you need to stop the appliance immediately, switch the On/

Oﬀ switch (6) to „0“.

10.2.2 Normal sequence

Release the throttle control (9). The engine idles. Then switch

the On/Oﬀ switch (6) to „0“.

10.3 Operation of the hedge trimmer:

1. Hold the hedge trimmer on its rear handle (8) and press

the throttle lock-out switch (7).

2. Hold the front handle (3) with your other hand.

3. Press the throttle trigger (9).

4. The cutting device will start moving.

If you release the throttle trigger, the cutting device will stop

and the engine will idle.

Contact the manufacturer if the cutting device still continues to

run in idle mode.

Do not continue working with the hedge trimmer in such a con-

dition.

10.4 Adjusting the rear handle (8).

To make working with the hedge trimmer easier it is possible

to choose one of the 3 working positions of the rear handle.

• When adjusting the throttle trigger (9) can not be pressed.

1. Use your left hand to hold the hedge trimmer on its front

handle (3).

2. Slide the locking handle (10) to the rear and turn the rear

handle to the desired position.

3. Release the locking handle (10). Make sure that the lock-

ing handle engages again and that the handle is secured.

10.5 Cutting blade (1) blockages

If the cutting blade (1) becomes blocked during operation,

switch oﬀ the hedge trimmer with the on/oﬀ switch (6) and

remove the spark plug connector (16).

Then remove the material that causing the blockage and check

the cutting blade (1) for possible damage.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 315808 PHS 9500 A1 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 5,86 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 315808 PHS 9500 A1 Manual

Product: