749300
19
Zoom out
Zoom in
Previous page
1/74
Next page
PBH 1050 B2
16 GBIE
Original accessories / auxiliary
equipment
Only use the accessories and additional
equipment which are specified in the
operating instructions and are compatible
with the appliance.
Operation
Additional handle
NOTE
For safety reasons, you should only use this
appliance with the additional handle
attached.
The appliance is fitted with an LED .
This lights up red as soon as the appliance is
connected to the power supply.
This indicates that the appliance is connected
to the power and that it will turn on immedi-
ately if the ON/OFF switch is pressed .
Loosen the strap on the additional handle by
turning it anticlockwise.
Push the additional handle in the direction of
the tool holder .
Turn the additional handle to the required
position.
The locking positions on the additional handle
must now be pushed over the locking pin on the
spindle of the appliance.
Turn the additional handle clockwise again
to tighten it.
NOTE
Move the additional handle into the
various locking positions depending on
your working position. Undo and lock the ad-
ditional handle as described previously.
Depth stop
Push the locking button for the depth stop
and keep it pushed in.
Insert the depth stop into the additional
handle .
Make sure that the teeth on the depth stop
point upwards and downwards.
Pull the depth stop out until the distance
between the tip of the drill and the tip of the
depth stop corresponds with the required
drilling depth.
Release the locking button for the depth stop
to lock the depth stop .
Fitting/removing a tool
WARNING!
Switch the appliance off and remove the
power plug before starting any work on the
appliance.
Fitting a tool:
Before fitting a tool into the tool holder ,
grease it lightly.
To insert, pull the locking collar backwards
and insert the tool.
Release the locking collar . This locks the
tool holder . Check that the tool is properly
locked by pulling it. The system has radial play
because of the design.
Removing a tool:
To remove the tool, pull the locking collar
backwards.
Quick-release chuck for round shaft
drill bits
WARNING!
Do not use the quick-release chuck
for hammer drilling or chiselling!
Set the function selector switch to the drill
symbol .
Inserting the quick-release chuck for round
shaft drill bits:
To insert the quick-release chuck (see also
fig. A) pull the locking collar backwards.
Insert the quick-release chuck .
Release the locking collar . This locks the
tool holder . Check that the tool is properly
locked by pulling it.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 311912 PBH 1050 B2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 311912 PBH 1050 B2 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 1,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info