748074

Parkside IAN 304379 POF 1200 C2 Manual

30
Zoom out
Zoom in
Previous page
1/140
Next page
30
GB IE
1. Place the machine with inserted cutter
on the workpiece to be processed.
2. Turn the step limit (14) until it engages in
the lowest step below the depth stop (17).
3. Loosen the clamping lever (19) by turn-
ing it upward.
Loosen the clamping lever (19) by
pushing it upward.
4. Slowly press down the machine until
the cutter contacts the workpiece.
5. Fasten the clamping lever (19) by turn-
ing it to the left.
Rough adjustment:
Release the locking screw (18) on the
depth limit (17).
6. Adjust the depth stop (17) to the de-
sired cutting depth, using the step limit
(14) if necessary, and tighten the lock-
ing screw (18).
Fine adjustment:
7. Set the scale below the rotary knob (2)
to the “0” position. For this purpose,
press the ring (2a) below the rotary
knob downward and turn it into the de-
sired position. If you have used the step
limit (14) for the rough adjustment, turn
it again until it engages in the lowest
step below the depth stop (17).
8. For the ne adjustment, turn the rotary
knob (2) to the desired measure, where-
in one complete rotation equals 1mm:
Counter-clockwise rotation:
greater cutting depth.
Clockwise rotation: lesser cutting depth.
Once you have set the desired
cutting depth, turn the step limit
(14) until it engages in the lowest
step below the depth stop (17).
We recommend testing the cutting
depth adjustment by means of a test
cut on a reject piece.
Gradual milling
To mill in multiple steps with greater cutting
depth, the cutting depth can be adjusted
with the step limit (
14).
1. Turn the step limit ( 14) so that it
engages in the highest step below the
depth stop (
17).
2. Set the further cutting depth with the
lower steps of the step limit ( 14).
Operation
Wear breathing protection
(ne dust mask of protection class
FFP2).
Do not wear gloves while milling.
Switching on and off
1. Connect the machine to the
power supply.
Make sure that the net voltage matches
the voltage rating indicated on the de-
vice’s type plate.
2. Switching on: Keep the safety lock (5)
pressed and press the on/off switch
(6). Then release the safety lock.
3. Switching off: Release the on/off switch
(6).
Pre-selecting the rotation
speed
You can pre-select the maximum rotation
speed on the handwheel for the rotation
speed pre-selection (
3).
• Adjust the desired rotation speed on
the handwheel for the rotation speed
preselection (
3).
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 304379 POF 1200 C2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 304379 POF 1200 C2 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 3,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info