Manual Parkside IAN 300503 PDFW 120 A1 (page 36 of 141) (English, German, Dutch, French, Portuguese, Spanish)

748031

Zoom out

Zoom in

1/141

PDFW 120 A1

■ 32 │ GB│IE

♦ Switch the appliance on by pressing the ON/

OFF switch .

♦ Set a speed suitable for the work using the

speed control .

♦ Switch the appliance oﬀ by pressing the ON/

OFF switch again.

Grinding

♦ Place the workpiece on the tool rest . Guide

the workpiece slowly towards the grinding disc

at the required angle until the workpiece

and the grinding disc come into contact with

each other.

♦ Move the workpiece evenly backwards and

forwards in order to achieve optimal results. This

also ensures that the grinding disc is worn

down more evenly.

Changing the grinding disc/buﬃng disc

WARNING! RISK OF INJURY!

►Always remove the power plug from the

wall socket before carrying out any work

on the appliance.

WARNING!

► The grinding or buﬃng disc used may

not be any larger than the prescribed diameter.

► Replace the grinding or buﬃng disc

when the outer diameter is less than 50mm.

NOTE

► Please note that you will require tools which

are not included in delivery for the assembly.

♦ Using a Phillips screwdriver, unscrew the ﬁxing

bolts from the side protective covers (see ﬁg.

E). Remove the protective covers on both sides.

♦ If you want to change the buﬃng disc ,

remove the locking pin

38a

from the attachment

on the ﬂexible shaft . Then pull the attach-

ment of the ﬂexible shaft oﬀ the shaft .

♦ Unscrew the union nut from the shaft

using a 17 mm wrench. Hold the aﬀected grind-

ing or buﬃng disc ﬁrmly in one hand to

create a suitable counterpressure.

♦ Remove the tension disc and grinding

or buﬃng disc .

♦ Place the new grinding or buﬃng disc on

the shaft .

♦ Push the tension disc back onto the shaft .

♦ Screw the union nut back onto the shaft .

♦ Re-tighten the union nut . Hold the grinding

or buﬃng disc that you have just attached

ﬁrmly in one hand to create a suitable counter-

pressure.

WARNING! RISK OF INJURY!

► Never use the grinding or buﬃng disc

without the protective cover .

CAUTION! PROPERTY DAMAGE!

► Do not tighten the union nut too tightly

since the grinding disc could otherwise

break.

♦ Reﬁt the protective cover and ﬁx it in place

by tightening the ﬁxing screws .

Fitting the ﬂexible shaft

WARNING! RISK OF INJURY!

►Always remove the power plug from the

wall socket before carrying out any work

on the appliance.

♦ Screw the ﬂexible shaft onto the connecting

thread of the appliance. To do this, push the

axle core of the ﬂexible shaft into the square

hole on the connecting thread . Turn the lock-

ing nut anticlockwise to tighten it.

WARNING – RISK OF INJURY!

► Make sure that the eye shields are folded

down to the tool rests . This can prevent

unintentional contact with the grinding or

buﬃng disc .

► After use, remove the ﬂexible shaft from

the appliance. Otherwise, the ﬂexible shaft

could start thrashing about in an uncon-

trolled manner and cause an injury when you

switch the appliance on.

My Double bench grinder IAN 300503 has completely lost its torque. It gets up to speed OK, but loses power as soon as any pressure is put on. Has anyone any ideas? ( I haven't used it for a while though). Submitted on 15-8-2021 at 18:49
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 300503 PDFW 120 A1 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 5,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 300503 PDFW 120 A1 Manual

Product: