748031

Parkside IAN 300503 PDFW 120 A1 Manual

35
Zoom out
Zoom in
Previous page
1/141
Next page
PDFW 120 A1 GB│IE │ 31 ■
♦ Now use the knurled screw to attach the
workpiece rest firmly onto the device. Ensure
that the spring washer and washer are properly
fitted (see fig. B).
Adjusting the tool rests
♦ Adjust the workpiece rests with the aid of
the knurled screws . Ensure that the space
between the grinding or the buffing disc
and the tool rest is as low as possible.
Ensure that the workpiece rests do not come
into contact with the grinding or the buffing
discs .
♦ Adjust the distance repeatedly as the grinding
or buffing disc wears down.
Fitting the spark deflectors
♦ Fit the spark deflectors with the aid of the
fixing bolts for the spark deflectors , nuts,
washers and spring washers to the top of the
device (see fig. C).
♦ Tighten the nuts using a pair of pliers or a 7 mm
open end wrench. Tighten the fixing bolts for
the spark deflector using a Phillips screw-
driver.
♦ Fit the spark deflectors so that the distance
between the grinding or buffing disc and
the spark deflector is as small as possible.
The gap should not be greater than 2 mm.
Ensure that the spark deflectors do not come
into contact with the grinding or the buffing
discs .
♦ Adjust the distance repeatedly as the grinding
or buffing disc wears down.
Fitting the eye shields
♦ Attach the eye shields to the fixtures provid-
ed on the spark deflectors using the mounting
screws for the eye shields , nuts, washers and
spring washers (see fig. C).
♦ Tighten the nuts using a pair of pliers or a 8 mm
open end wrench. Tighten the fixing bolts for
the eye shields using a Phillips screwdriver.
Working procedures
Ensure that the appliance is always stable
and secure. For extra safety, you can secure
the appliance in a suitable location. There are
two drill holes in the housing foot that can
be used for attachment to a secure and level
surface. Feed a suitable fixing material that
is appropriate for the surface (not supplied)
through the 2 drill holes . Fix the appliance
to the surface using the fixing material.
Ensure that the grinding and buffing discs
are not blocked.
Ensure that the eye shields , spark deflec-
tors and tool rests are properly fitted
and adjusted!
A light grinding pressure is sufficient:
Work using a light grinding pressure – a constant
and correct speed will ensure the best grinding
performance.
Grinding:
Bear in mind that the workpiece heats up during
grinding. Therefore, cool the workpiece in a water
bath. Dry it thoroughly before you resume working.
Operation
Switching on and off
■ Direction of rotation of the tool!
NOTE
► Before first use, allow the grinding and buff-
ing discs to run without a load at top speed
for about 5 minutes. When doing so, stay out of
the hazard area in front of and next to the open-
ings in the grinding or the buffing disc .
WARNING – RISK OF INJURY!
► Ensure the lowest-possible distance (gap)
between the grinding or the buffing disc
and the tool rest .
► If the appliance suddenly brakes completely
or jams, it must be switched off immediately.
♦ Set the eye shields so that they provide the
greatest possible protection.
… 35 …


Need help? Post your question in this forum.

Forumrules
1

Forum

parkside-ian-300503-pdfw-120-a1

Reset search

  • My Double bench grinder IAN 300503 has completely lost its torque. It gets up to speed OK, but loses power as soon as any pressure is put on. Has anyone any ideas? ( I haven't used it for a while though). Submitted on 15-8-2021 at 18:49

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 300503 PDFW 120 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 300503 PDFW 120 A1 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 5,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info