747887

Parkside IAN 292293 PDBG 125 A1 Manual

25
Zoom out
Zoom in
Previous page
1/97
Next page
Q Lubrication
This product features a lubrication system utilizing
wax sticks
23
to clean and lower friction between
the two blades rotating in counter-direction.
1. Insert a wax stick
23
into the wax stick
holder
4
(see fig. E).
2. Turn the wax stick dial
3
clockwise until it
touches the blades.
3. Slightly turn the wax stick dial
3
counter-
clockwise to create a little clearance between
wax stick
23
and blades.
4. Occasionally turn the wax stick dial
3
slightly clockwise during operation to
lubricate the blades.
Q Attaching / removing a dust
extraction device
WARNING!
u During operation fine dust will be generated!
Some dusts are highly inflammable and
explosive! Always attach a dust extraction
device when using this product in order to
keep the working area clean! Wear a dust
mask when operating this product! Dust can
be harmful to health! Especially dust and
chips of wood that has been treated, e.g.
with wood preservative or a stain!
u Do not smoke during operation, keep heat
sources and open flames out of the working
area!
This product features a designated dust extraction
outlet
12
to connect a vacuum cleaner reducing
generated dust during operation on the workpiece
and airborne.
1. Slide the dust extraction adaptor
24
over the
dust extraction outlet
12
, make sure it sits
snug.
2. Rotate the dust extraction adaptor
24
to your
needs (see fig. F).
3. Remove the dust extraction adaptor
24
after
work by simply pulling it off.
Q Operation
CAUTION! RISK OF INJURY!
u Keep your hands away from the tool when
the product is in operation.
Q Cutting guide
The cutting guide
5
can be adjusted for different
working positions.
1. Use the provided multi-tool
22
to loosen the
cutting guide screw
6
(see fig. G).
2. Turn the cutting guide
5
to your desired
position.
3. Use the provided multi-tool
22
to tighten the
cutting guide screw
6
.
Q Switching on and off
Switching on:
1. Push the lock-off button
15
and keep it pressed.
2. Press the on / off switch
13
. Release the lock-off
button
15
once the product is running.
Switching off:
1. Release the on / off switch
13
to switch the
product off.
Q Cutting
This product features two counter-rotating blades,
cancelling each other’s pull force out, which makes it
ideal to perform cross and pocket cuts safely.
Cross cut
NOTE
u Always perform a trial cut into scrap
material along a marked cutting line on the
workpiece. The cutting guide indicates where
the cut will be made.
1. Secure the workpiece with suitable means.
2. Hold the product firmly with both hands on the
rear handle
14
and front handle
1
.
3. Switch on the product (see “Switching on and
off”). Let the blades reach full speed.
4. Guide the product into the workpiece to make
the cut.
5. Switch off the product and let the blades come to
full stop.
6. Lift the product off the workpiece.
7. Fig. H: rip cutting of chipboard or plywood (left);
cross cutting of natural timber (right).
8. Fig. I: cross cutting of a copper pipe (left);
cross cutting of an aluminum bar (right).
27 GB / IE
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 292293 PDBG 125 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 292293 PDBG 125 A1 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 2,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info