Manual Parkside IAN 292291 PBS 350 A1 (page 25 of 72) (English, German, Dutch, French)

747882

Zoom out

Zoom in

1/72

GB/IE18

• Before you connect the machine to the power supply, make

sure the data on the rating plate is the same as that for

your mains.

9. Attachment

ATTENTION!

Before all maintenance, set-up and assembly work on the

band saw, unplug the mains plug.

Assembly tools

1 Open-ended spanner, size 10/13

1 Allen key, size 3

1 Allen key, size 4

1 Screwdriver

The saw table is not assembled for packaging reasons.

9.1. Assembling the saw table (Fig. 2-4)

• Remove the wing nut (31), the locking handle (20), the two

washers and the clamping plate (32). (Fig. 2)

• Remove the two knurled nuts (33), the U-reinforcement (34)

and the two countersunk screws M6x16 from the saw ta-

ble. (Fig. 3)

• Guide the saw table (7) over the Bandsaw blade (21).

Fasten it to the two screws on the machine frame with the

plate (32), the two washers, the wing nut (31) and the lock-

ing handle (20). (Fig. 4)

• Fasten the U-reinforcement (34) to the front side of the saw

table with 2 countersunk screws M6x16 and 2 knurled

nuts (33). (Fig.3)

9.2. Tensioning the saw band (Fig. 1a)

• ATTENTION! If the saw is at a standstill for an extended

period the saw band tension must be relieved, i.e. before

switching the saw on it is necessary to check the saw blade

tension.

• Turn the clamping screw (1) clockwise to tension the Band-

saw blade (21). The correct tension of the saw band can

be determined by pressing the ﬁnger laterally against the

saw band, roughly centrally between the two saw band

rollers (2+8). The Bandsaw blade (21) should only depress

slightly (approx. 1-2 mm) here.

• The suﬃciently tensioned saw band makes a metallic sound

when tapped.

• Relieve the saw band tension if it is not in use for an ex-

tended time, so that it does not become overstretched.

• ATTENTION! With high tension, the saw band may break.

RISK OF INJURY! If the tension is too low, the driven saw

band roller (8) may spin, resulting in the saw band com-

ing to a standstill.

9.3 Adjusting the saw band (Fig. 1a+1b)

• ATTENTION! Before it is possible to implement the saw

band setting, the saw band must be tensioned correctly.

• Open the side covers (11) by undoing the cover locking

mechanisms (10) with the help of the screwdriver (29).

• Slowly turn the saw band roller (2) clockwise. The Band-

saw blade (21) should run centrally on the saw band roller

(2). If this is not the case, the angle of the top saw band

roller (2) must be corrected.

• If the Bandsaw blade (21) runs more towards the rear edge

of the saw band roller (2) then the set screw (14) must be

rotated anticlockwise.

• Open the locking screw for the top saw band roller (13).

• Turn the bottom saw band roller (8) slowly by hand, to

check the position of the Bandsaw blade (21).

• If the Bandsaw blade (21) runs more towards the front

edge of the saw band roller (2) then the set screw (14)

must be rotated clockwise.

• After setting the top saw band roller (2), check the position

of the Bandsaw blade (21) on the bottom saw band roller

(8). The Bandsaw blade (21) should also lie centrally on

the saw band roller (8) here. If this is not the case, the an-

gle of the top saw band roller (2) must be adjusted again.

• Turn the saw band roller a few times, until the adjustment

of the top saw band roller (2) acts on the saw band posi-

tion on the bottom saw band roller (8).

• Tighten the locking screw for the top saw band roller (13).

• Once adjustment is complete, close the side covers (11)

again and secure with the cover locking mechanisms (10)

with the help of the screwdriver (29).

9.4. Adjusting the saw band guide (Fig. 5 - 8)

Both the support bearing (36 + 42) and the guide pins (37 +

46) must be readjusted after every saw band change.

• Open the side covers (11) by undoing the cover locking

mechanisms (10) with the help of the screwdriver (29).

9.4.1. Top support bearing (36) ( Fig. 5)

• Undo Allen screw for top support bearing (35).

• Move support bearing (36) suﬃciently far that it just no

longer touches the Bandsaw blade (21) (distance max.

0.5 mm).

• Retighten the Allen screw for the top support bearing (35).

9.4.2. Adjusting the bottom support bearing (42)

(Fig. 7)

• Disassemble the saw table as per 9.1 in the opposite di-

rection.

• Undo Allen screw for bottom support bearing (41).

• Move bottom support bearing (42) suﬃciently far that it

just no longer touches the Bandsaw blade (21) (distance

max. 0.5 mm).

• Retighten Allen screw for bottom support bearing (41).

9.4.3. Adjusting the top guide pins (37)

• Undo Allen screws for top retainer (40)

• Move top retainer (39), top guide pins (37), until the front

edge of the guide pins (37) is approx. 1 mm behind the

tooth base of the saw band.

• Retighten Allen screws for top retainer (40).

• ATTENTION! The saw band will be unusable if the teeth

touch the guide pins with the saw band running.

• Undo Allen screws for top guide pins (38).

• Slide the guide pins (37) in the direction of the saw band!

Attention! The distance between the guide pins (37) and

Bandsaw blade (21) must not exceed 0.5 mm. (Saw band

must not jam)

• Retighten Allen screws (38).

• Turn the top saw band roller (2) a few times in a clock-

wise direction.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 292291 PBS 350 A1 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 292291 PBS 350 A1 Manual

Product: