Manual Parkside IAN 292291 PBS 350 A1 (page 24 of 72) (English, German, Dutch, French)

747882

Zoom out

Zoom in

1/72

GB/IE 17

• Blades that are misshapen or damaged in any way must

not be used.

• If the table insert is worn, replace it.

• Never operate the machine if either the door protecting the

blade or the detachable safety device are open.

• Ensure that the choice of blade and the selected speed are

suitable for the material to be cut.

• Do not begin cleaning the blade until it has come to a

complete standstill.

• For straight cuts of small workpieces against the longitudi-

nal limit stop the push stick has to be used.

• Wear gloves when handling the saw blade and rough

materials

• The bandsaw blade guard should be in its lowest position

close to the bench during transport.

• For miter cuts when the table is tilted, the parallel stop must

be positioned on the lower part of the table.

• Never use guards to lift or transport items.

• Ensure that the bandsaw blade guards are used and cor-

rectly adjusted.

• Keep your hands a safety distance away from the band-

saw blade. Use a push stick for narrow cuts.

• The push stick has to be stored on the intended device, so

that it can be reached from normal working position and

is always ready to be used.

• In the normal operating position the operator is in front

of the machine.

6. Technical data

Electro motor

230 - 240 V ~ 50 Hz

Power S1 250W, S2 30 min 350W

Revolutions n

1400 min

-1

Saw band length

1400 mm

Saw band width

3,5-12 mm

Saw band width max.

12 mm

Cutting speed

900 m/min

Passage height

0 - 80 mm

Passage width

200 mm

Table size

300 x 300 mm

Slewing range of the table

0° bis 45°

Max. size of the

workpiece

400 x 400 x 80 mm

Overall weight

16,5 kg

Subject to technical modiﬁcations!

* Operating mode S1, continous operation.

* Operating mode S2, short-term operation with constant

load; Duration of nominal operation

The work piece must have a minimum height of 3 mm and a

minimum width of 10 mm.

The total noise values determined in accordance with EN

61029.

Sound pressure level L

77,4 dB(A)

Uncertainty K

3 dB

Sound power level L

90,4 dB(A)

Uncertainty K

3 dB

Wear hearing protection.

The eﬀects of noise can cause a loss of hearing. Keep the

noise level and vibration to a minimum!

• Only use faultless devices.

• Maintain and clean the device at regular intervals.

• Adapt your working methods to the device.

• Do not overload the device.

• Have the device checked if necessary.

• Switch the device oﬀ if it is not in use.

7. Remaining hazards

The machine has been built using modern technology in ac-

cordance with recognized safety rules. Some remaining haz-

ards, however, may still exist.

• Risk of injury for ﬁngers and hands by the rotating saw

band due to improper handling of the work piece. Risk of

injury through the hurling work piece due to improper han-

dling, such as working without the push stick.

• Risk of damaging your health due to wood dust and wood

chips. Wear personal protective cloth such as goggles. Use

a ﬁtting dust extractor.

• Risk of injury due to defective saw band. Regularely check

saw band for such defects.

• Risk of injury for ﬁngers and hands while changing saw

band. Wear proper gloves.

• Risk of injury due to starting saw band while switching on

the machine.

• The use of incorrect or damaged mains cables can lead to

injuries caused by electricity.

• Wear only closeﬁtting clothes. Remove rings, bracelets and

other jewelry.

• For the safety of long hair, wear a cap or hair net. Even

when all safety measures are taken, some remaining haz-

ards which are not yet evident may still be present.

• Remaining hazards can be minimized by following the in-

structions in „General safety instructions“ „Proper Use“ and

in the entire operating manual.

8. Before starting the equipment

Make sure the machine stands securely, i.e. bolt it to a

workbench or solid base. There are two holes for this purpose

in the machine foot.

• The saw table must be mounted correctly.

• All covers and safety devices have to be properly ﬁtted

before the machine is switched on.

• It must be possible for the blade to run freely.

• When working with wood that has been processed before,

watch out for foreign bodies such as nails or screws etc.

• Before you actuate the On/Oﬀ switch, make sure that the

saw blade is correctly ﬁtted and that the machine’s moving

parts run smoothly.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 292291 PBS 350 A1 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 292291 PBS 350 A1 Manual

Product: