Manual Parkside IAN 285802 PDFW 120 A1 (page 32 of 138) (English, German, Dutch, French, Portuguese, Spanish)

746566

Zoom out

Zoom in

1/138

PDFW 120 A1

■ 28 │ GB

│

a) Hold the power tool ﬁrmly in both hands

and position your body and arms so they

can absorb the force of a kickback. By taking

adequate precautions, the operator can stay in

control of the kickback forces.

b) Take special care when working around

corners, sharp edges, etc. Avoid allowing the

accessory tool to bounce back from the work-

piece or jam in the workpiece. The rotating

accessory tool is more likely to jam in corners or

sharp edges or if it rebounds oﬀ them. This can

cause a loss of control or kickback.

c) Do not use toothed saw blades. Such acces-

sories often cause a kickback or loss of control

over the power tool.

d) Always move the accessory tool in the same

direction in the material in which the cutting

edge leaves the material (in other words, the

same direction in which the dust is thrown

out). Guiding the power tool in the wrong direc-

tion will cause the cutting edge of the accessory

tool to jump out of the workpiece which can

lead to the accessory tool being pulled in this

direction.

e) Always ﬁx the workpiece when using rotary

ﬁles, cutting discs, high-speed milling tools or

hard-metal tools. Even a minimal tilting in the

groove can cause these tools to jam and lead

to a kickback. When the cutting disc jams, it

usually breaks. When a rotary ﬁle, high-speed

milling tool or hard-metal milling tool jams, the

accessory tool can jump out of the groove and

lead to loss of control of the power tool.

Supplementary safety instructions

for grinding and abrasive cutting

Special safety instructions for grinding and

abrasive cutting:

a) Use only the grinding accessories approved

for your power tool and only for the recom-

mended applications. Example: Never grind

with the side surface of a cutting disc. Cutting

discs are designed to remove material with the

edge of the disc. Any lateral application of

force on these grinding tools can lead to break-

age.

b) Use only undamaged mandrels of the correct

size and length and without undercut on the

shoulder for conical and straight pencil grind-

ers. Using an appropriate mandrel reduces the

risk of breakages.

c) Avoid cutting disc jams or excessive contact

pressure. Do not make any excessively deep

cuts. Overloading the cutting disc increases the

stress and likelihood of tilting or blocking and

thus the possibility of a setback or a breakage

of the grinding tool.

d) Avoid putting your hand in the area in front

of or behind the rotating cutting disc. When

you move the cutting disc away from your hand,

it is possible, in the event of a kickback, that the

power tool along with the rotating disc could be

thrown out directly towards you along with the

rotating disc.

e) If the cutting disc jams or you stop working,

switch the tool oﬀ and hold it steady until the

disc has completely stopped turning. Never

attempt to pull a rotating cutting disc out of a

cut. This could lead to kickback. Identify and

remove the cause of the jam.

f) Do not switch the power tool back on as long

as it is in the workpiece. Allow the cutting disc

to reach its full speed before you carefully

continue the cut. Otherwise, the disc may jam,

jump out of the workpiece or cause kickback.

g) Support panels or large workpieces to re-

duce the risk of the cutting disc jamming and

causing a kickback. Large workpieces can

bend under their own weight. The workpiece

must be supported on both sides, namely in the

vicinity of the cut, and also at the edge.

h) Be particularly careful when making “pocket

cuts” into existing walls or other obscured ar-

eas. The inserted cutting disc may cut into gas

or water pipes, electrical wiring or other objects

that can cause kickback.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 285802 PDFW 120 A1 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 1,73 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 285802 PDFW 120 A1 Manual

Product: