746415
17
Zoom out
Zoom in
Previous page
1/68
Next page
18 GB/IE
… / Cleaning and ... / Environmental ... / Environmental ... / TroubleshootingSafety instructions / Initial use
Replace the protective visor if
scratches or damages appear.
The welding helmet does not pro-
vide protection against impact.
Frequent use, cleaning or storage
can mean that the service life is
less than 6 years. Replace the
welding helmet immediately if
the viewing panel gets scratched
or the viewing panel is visibly
damaged in any other way.
ATTENTION! Materials that
come into contact with the wearer‘s
skin
may cause allergic reactions in
peo
ple with sensitive skin.
ATTENTION! Eye protection
can represent a hazard for the
wearer if it is worn over normal cor-
rective glasses due to the impact
from high-speed particles.
ATTENTION! If protection
against high-speed particles at
extreme temperatures is required,
the eye protection chosen must be
labelled with the letter T directly af-
ter the letter for the impact intensity,
i. e. FT, BT or AT. If the letter for the
impact intensity is not followed by
the letter T, the eye protection may
only be used against high-speed
particles at room temperature.
Initial use
Note: Only use the welding helmet with the rear
pane mounted
4
.
Note: Keep the UV filter‘s sensors
8
clean and
clear.
Check that the welding helmet and the protective
screen are intact before each use. If the protective
screen has scratches, cracks or irregularities, it must
be replaced before use, as serious injuries may oc-
cur otherwise.
Remove the protective film from the inside and
the outside of the visor.
Put on the welding helmet with the help of the
headband
5
. Press the adjustment buttons
6
to make the welding helmet tighter and the ad-
justment button
7
, to fix the welding helmet.
When adjusting, ensure that your head is placed
as far into the helmet as possible and that it sits
as close as possible to your face.
Set the appropriate darkening shade before the
welding procedure (see the following table).
The darkening shade may be manually adjusted
from 9 to 13 by twisting the darkening regula-
tor
9
on the outside of the helmet.
ATTENTION! The darkening regulator
9
has
the setting position “grind“. If the darkening
regulator
9
is set to this position the automatic
darkening is deactivated.
Only use this setting when you do not wish to
use the welding helmet for welding. The auto-
matic darkening is then no longer active.
Check the light density before each use.
Test procedure: Bring the viewing panel closer
to an external light source with a value of more
than 40 W and examine whether or not the
screen darkens or illuminates.
To change the UV filter / solar cells, push in both
tabs and pull the front frame outward. Fig. B
(Item no. 2000) or loosen the two screws as
shown in Fig. A (Item no. 2001, 2002).
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 281392 PSH 3 A2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 281392 PSH 3 A2 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 0,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info