746153
11
Zoom out
Zoom in
Previous page
1/96
Next page
1 1
GB
Edit not work pieces that you can not sure
retain. Especially round or uneven
workpieces.
Assembly
The bench drill is supplied disassembled.
Clean the column tube (14), baseplate
(17), drilling bench (20), vice (23) and
the drill chuck (4) beforehand, with a dry
cloth.
1. Place the column tube (14) on the ba-
seplate (17). Bolt the column tube (14)
to the baseplate (17) with the three as-
sembly srews (16) supplied. Tighten the
assembly srews (16) moderately tight
so that the threads in the baseplate (17)
do not strip.
2. Place the drilling bench (20) on the co-
lumn tube (14). Push the drilling bench
(20) into a lower position. Use the
locking handle (15) to x the drilling
bench (20) in a lower position.
K L M N O P Q R S T
U V W X Y Z
A
B C D E F G H I J
3. Place the vice (23) on the drilling
bench (20) and screw it with the
enclosed mounting bolts (22)
tightly to the drilling bench (20).
K L M N O P Q R S T
U V W X Y Z
A B
C D E F G H I J
4. Place the motor unit (13) on the
column tube (14) and secure the
motor unit (13) with the clam-
ping screw (27) to the side with
the allen key (25) supplied.
K L M N O P Q R S T
U V W X Y Z
A B C
D E F G H I J
5. Bolt the three drill lifting arms
into the spindle guide (9). Tigh-
ten the three hole lifting arms
with a spanner (AF 6 mm).
6. Release the clamping screw from
the depth stop (8).
K L M N O P Q R S T
U V W X Y Z
A B C D
E F G H I J
7. Put the safety device (6) on the
upper part of the drill spindle (7).
8. Secure the safety device (6) with
the clamping screw (28).
9. Fold the safety device (6) up-
wards. Insert the chuck (4) on
the taper of the drill spindle (7).
Push the drill chuck onto the drill
chuck tip with a few light taps.
Use a plastic hammer for this
purpose.
Operation
Caution! Risk of injury!
- Ensure that you have sufcient
space in which to work and that
you do not endanger other people.
- All hoods and protective devices
must be assembled properly be-
fore commissioning.
- Disconnect the mains plug be-
fore changing the setting on the
device.
Setting up
Place the bench drill on a solid surface.
Ideally, bolt the drill to the surface. Use the
four holes in the baseplate (17) for this.
K L M N O P Q R S T
U V W X Y Z
A B C D E
F G H I J
Selecting the speed
1. Release the locking bolt (11) on the
gear cover (3).
2. Open the gear cover (3).
3. Release the two retaining bolts (12) on
the motor unit (13).
4. Slide the motor unit (13) forward a little
to release the load on the V-belts (29).
5. Place the V-belts (29) on the desired
assembly to reach the specied speed:
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 276419 PTBM 500 C3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 276419 PTBM 500 C3 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 2,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info