745542
14
Zoom out
Zoom in
Previous page
1/60
Next page
PDWS 125 A1
GB
IE
 11
Operation
Operating a compressed air tool
NOTE
In order to achieve the full power available
from your compressed air tool, always
use compressed air hoses with an internal
diameter of at least 9 mm. A lower internal
diameter can considerably reduce the power.
CAUTION!
Do not use a compressed air line that con-
tains any water condensation.
The tool must be sufficiently supplied with
pneumatic oil to ensure long service life. This
can take place as follows:
Use oiled compressed air by fitting a mist
lubricator.
Without a mist lubricator: add oil manu-
ally through the compressed air connec-
tion
every day. Approx. 3-5 drops
of pneumatic oil for every 15 operating
minutes during continuous use.
If the tool has been out of operation for sev-
eral days, add around 5 drops of pneumatic
oil manually through the compressed air
connection .
Allow the tool to run at idling speed for a
short time.
Always guide the machine using both hands.
Switch on first, then apply the accessory tool
to the workpiece.
After switching off, only put the machine down
once the motor has come to a standstill.
1.) Attach a suitable accessory tool.
2.) Adjust the operating pressure (measured
at the air intake when the compressed air
tool has been switched on). Please refer to
the section entitled "Technical data" for the
maximum permissible operating pressure
3.) Connect the compressed air tool to the com-
pressed air supply.
4.) Switching on: Push the safety lock-out
towards and press the ON/OFF switch .
5.) Switching off: Release the ON/OFF switch
.
Working procedures
Sanding:
Press the machine against the workpiece moder-
ately and move it backwards and forwards over
the surface so that the workpiece surface does
not become too hot.
Rough grinding:
Work using an angle of incidence of between
30° and 40° for good working results.
NOTE
Never use cutting discs for rough grinding.
Abrasive cutting:
Always work against abrasive cutting (see Fig-
ure 3). Otherwise there is a risk that the ma-
chine can jump out of the cut in an uncontrolled
manner. Work using moderate forward speed
appropriate to the material being processed.
Do not tilt, do not press, do not oscillate.
Fig. 3
NOTE
Never use rough grinding discs for cutting.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 276009 PDWS 125 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 276009 PDWS 125 A1 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info