745555
73
Zoom out
Zoom in
Previous page
1/204
Next page
73
FR BE
Régler / monter le coin à
fendre
(Fig. 16-19)
Attention !

réglage de la lame de scie (5)

changement de la lame de scie.
1. Régler la lame de scie (5) sur la pro-
fondeur de coupe maximale, l‘amener
en position 0° et la bloquer.
2. Démonter la protection de lame de
scie (2)
3. Retirer le plateau de table (6).
 
5. Pousser le coin à fendre (4) vers le
haut.
6. Lécart entre lame de scie (5) et coin
à fendre (4) doit être de max. 8 mm
max. (Fig.19)
 
monter le plateau de table (6).
8. Remonter la protection de lame de
scie (2).
Montage / remplacement
de la lame de scie
(Fig. 22)
 
secteur et porter des gants de
protection.
2. Démonter la protection de lame de
scie (2)
3. Retirer le plateau de table (6) en des-
serrant les trois vis à tête fraisée (29)

2. Démonter la vis avec l‘écrou papillon
et la rondelle de serrage (27) de la
protection de lame de scie (2). Placer
la protection de la lame de scie (2)
par le haut dans le coin à fendre (4).
3. Monter la vis avec l‘écrou papillon et
la rondelle de serrage (27) de manière


4. Ne pas trop serrer la vis (27). La pro-
tection de la lame de scie doit rester
mobile.
5. Positionner le tuyau d‘aspiration (3)
sur l‘adaptateur d‘aspiration (16) et les
supports d‘aspiration de la protection
de la lame de scie (2). Raccorder un
dispositif d‘aspiration des copeaux
sur l‘adaptateur d‘aspiration (16),

6. Le démontage se fait en sens inver-
se. Attention ! Avant de commencer
à scier, la protection de la lame de
sciage (2) doit être abaissée sur la
marchandise à scier.
Remplacer le plateau de
table
(Fig. 17 et 22)
1. En cas d‘usure ou de détérioration, le
plateau de table (6) doit être échangé,
sans quoi il existe un risque de blessu-
re plus important.
2. Retirer les 3 vis à tête fraisée (29).
3. Retirer le plateau de table (6) usé.
4. Le montage du nouveau plateau de
table se fait en sens inverse.
73


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 273460 PTK 2000 B2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 273460 PTK 2000 B2 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 3,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info