745236
12
Zoom out
Zoom in
Previous page
1/96
Next page
12
GB IE
as needed, so that the cutter can
be inserted.
3. Release the spindle locking but-
ton (16).
4. Insert the desired cutter into the
already mounted collet chuck
(13). The cutter shaft must be
pushed in at least 20 mm.
5. Use the combination wrench (27)
to tighten the cap nut (8) while
keeping the spindle locking but-
ton (16) pressed.
Tighten the cap nut only when a
cutter is inserted. The collet chuck
might get damaged.
Change collet chuck
All cutters of the 6-part cutter set included
in the delivery are provided with an 8-mm
cutter shaft.
Change the collet chuck for cutters with a
6-mm cutter shaft.
1. Press the spindle locking button
(16) on the front side of the ma-
chine and keep it pressed down.
2. Screw off the cap nut (8) using
the combination wrench (
27).
3. Release the spindle locking but-
ton (16).
4. Take out the 8-mm collet chuck
(13) and insert the 6-mm collet
chuck (22) that is included in the
delivery.
5. Screw the cap nut (8) loosely
back on.
6. Insert a cutter as described above
.
Tighten the cap nut only when a
cutter is inserted. The collet chuck
might get damaged.
Connecting the suction
adapter
You can reduce dust formation while you
work by connecting a dust suction system.
1. Fit the suction adapter (20) on
the provided drill holes (
12)
in the baseplate (10).
2. Screw on the 2 recessed head
screws (21) from the bottom side
of the baseplate (10).
3. Fit the reducer part (30) on the
suction adapter if needed.
4. Connect the suction hose of a
vacuum cleaner to the suction
adaptor (20).
The vacuum cleaner must be suit-
able for the workpiece to be pro-
cessed.
Use a special vacuum cleaner if
dusts with hazard for health are cre-
ated.
Mounting the parallel stop
1. Screw both screws out of the
guide bars (29).
2. Screw the guide bars (29) onto
the parallel stop (24).
Adjust cutting depth
1. Place the machine with inserted
cutter on the workpiece to be pro-
cessed.
2. Turn the step limit (14) until it
engages in the lowest step below
the depth stop (17).
3. Release the locking screw (18) on
the depth limit (17).
4. Loosen the clamping lever (19)
by pushing it upward.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 114253 POF 1200 B2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 114253 POF 1200 B2 in the language / languages: English, German, Dutch, Swedish as an attachment in your email.

The manual is 2,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info