745458
13
Zoom out
Zoom in
Previous page
1/88
Next page
13
GB IE
justable screw (21) with a ring
spanner. The tape run accuracy is
set by the turning the adjustable
screw (21) with a screwdriver.
7. Check the tape run by manually
turning the grinding belt.
8. Re-tighten the nut (21a).
Change grinding disc
Information on replace-
ment:
Never operate the device without
protective equipment.
Ensure that the rotation speed
stated on the grinding disc (
19) is the same or higher than
the nominal rotation speed of the
device.
Ensure that the grinding disc
dimensions match those of the
device.
Only use awless grinding discs
(ringing test: when you strike the
grinding disc with a plastic ham-
mer, it results in a clear sound).
Never re-drill a locating hole
which is too small to make it
larger.
Never use separate bushings or
adapters in order to make grind-
ing discs whose hole is too large
t the device.
Do not use any saw blades.
To clamp the grinding tools only
use the clamping ange provid-
ed. The pads between the clamp-
ing ange and the grinding tools
must be made of elastic materials
e.g., rubber, soft cardboard etc.
Always reassemble the device
completely after replacing the
grinding disc.
Switch the device off and remove
the mains plug.
Allow the device to cool down.
Wear protective gloves when
changing the grinding discs in or-
der to avoid cutting damages.
1. Remove the spark protection (
1) (see „Assemble/set spark pro-
tection).
2. Loosen the 3 xing screws (15)
and remove the grinding disc
cover (16).
3. Loosen the xing screws (11) and
remove the grinding belt cover
(12) (see „Changing the grinding
belt“).
4. Unscrew the grinding disc nut
(19a) in the clockwise direction,
by holding the nut of the opposite
roller of the grinding belt in place
(see small image).
5. Remove the clamping ange
(19b) and the grinding disc (19).
6. Set up the new grinding disc (19)
and the clamping ange and
manually screw the grinding disc
nut (19a) in the anti-clockwise
direction.
7. Screw the grinding disc cover
(16).
8. Set the spark protection ( 1)
and the workpiece support (
18) so that the distance between
the grinding disc (19) is max.
2mm (see „Assembly“).
The grinding disc nut must not be
screwed too tightly in order to
avoid a breaking of the grinding
disc and nut.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 113076 PSBS 240 B2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 113076 PSBS 240 B2 in the language / languages: English, German, Dutch, French, Swedish as an attachment in your email.

The manual is 1,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info