745458
12
Zoom out
Zoom in
Previous page
1/88
Next page
12
GB IE
Keep your hands away from
the grinding disc and grind-
ing belt when the device is in
operation. Injury hazard!
Switching on and off
Ensure that the mains voltage
matches the specications on the
rating plate.
Connect the equipment to the mains.
1. To switch on, press the I On switch
and the device starts up (see 14a).
2. To switch off, press the 0 off switch
and the device switches off (see
14b).
After switching on the device, wait until the
device has reached its max. speed. Only
then must you start with the grinding.
The disk will continue to
run after the equipment is
switched off. There is a risk
of injury.
Test run:
Before starting work and after each
change of grinding disk, carry out a test
run of at least 60 seconds with no load.
Switch off the equipment immediately if the
disk runs lumpy, substantial vibrations oc-
cur, or abnormal noises are generated.
Grinding with the grinding
disc
The arrow on the protective hood
(3) shows the direction of rota-
tion of the grinding disc.
Place the workpiece on the workpiece
support ( 18) and slowly bring it to
its desired angle on the grinding disc
(19).
Move the workpiece slightly from side
to side in order to achieve an optimal
grinding result. This way, the grinding
disc is worn uniformly. Occasionally,
allow the workpiece to cool down.
Tape loops
The arrow on the protective hood
(9) shows the direction of rota-
tion of the grinding belt.
Firmly hold the workpiece, do not exert
any strong force.
Move the workpiece slightly from side
to side in order to avoid a one-sided
wear of the grinding belt.
Always grind the pieces of wood in the
direction of the wood grain in order to
avoid chipping.
Change grinding belt
1. Loosen the 3 xing screws (11)
and hang out the grinding belt
cover (12).
2. Loosen the clamping screw (8) by
a few rotations.
3. Press the clamping lever (7) down-
wards and detract the grinding
belt (10).
4. Place the new grinding belt (10)
in the centre on the upper (20a)
and lower (20b) rollers and let go
of the clamping lever (7).
5. Tighten the clamping screw (8) and
mount the grinding belt cover (12).
Set the tape run:
6. Loosen the nut (21a) of the ad-
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 113076 PSBS 240 B2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 113076 PSBS 240 B2 in the language / languages: English, German, Dutch, French, Swedish as an attachment in your email.

The manual is 1,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info