458602

Paradyne FrameSaver NP 110 Manual

170
Zoom out
Zoom in
Previous page
1/175
Next page
Appendix
980-001-0240B FrameSaver NP 110 User’s Manual - Installation Guide A-13
November
2000
V54 User Lp to Netw Loopback is in place at the User Port toward the Network Circuit, in response to a
V.54 LoopUp code from the Network (only if DS0s are assigned to the User Port.)
Line Lp to DSX Full T1 Line Loopback in place toward the DSX Circuit.
Payld Lp to DSX Full T1 Payload loopback in place toward the DSX Circuit.
QRSS to DSX Full T1 QRSS pattern BERT is being sent toward the DSX Circuit.
DSX 2047 to Netw 2047 pattern BERT is being sent toward the Network Circuit (for DS0s assigned to
DSX Port @ Nx56K.)
DSX Zero to Netw All Zeros pattern BERT is being sent toward the Network Circuit (for DS0s assigned
to DSX Port @ Nx56K.)
2047 to DSX 2047 pattern BERT is being sent toward the DSX Circuit (for DS0s assigned to DSX
Port @ Nx56K.)
DSX Lp to Netw Loopback is in place at the DSX Port (for DS0s assigned to DSX Port @ Nx64K)
toward the Network Circuit.
DSX CFA/Red Alarm Detected loss of DSX Circuit Facility. Framing must be enabled for DSX.
DSX Rmt/Yellow Alarm Carrier alarm notification that Transmit failure from this DCE has been detected on
this DSX Circuit Facility. Framing must be enabled for DSX.
DSX AIS/Blue Alarm Carrier alarm notification that an upstream signal failure has been detected on this
DSX Circuit Facility. Framing must be enabled for DSX.
Lp to Drop Loopback is in place at the Drop Port toward the Drop Circuit.
Drop Lp to Netw Loopback is in place at the Drop Port toward the Network Circuit.
Drop 2047 to Netw 2047 pattern BERT is being sent toward the Network Circuit (for DS0s assigned to
Drop Port).
Drop Zero to Netw All Zeros pattern BERT is being sent toward the Network Circuit (for DS0s assigned
to Drop Port).
2047 to Drop 2047 pattern BERT is being sent toward the Drop Circuit.
V54 Drop Lp to Netw Loopback is in place at the Drop Port toward the Network Circuit, in response to a
V.54 LoopUp code from the Network (only if DS0s are assigned to the Drop Port.)
LL to Drop Loopback is in place at the Drop Port toward the Drop Circuit, in response to an LL
(Local Loopback) signal at the Drop Port interface (only if DS0s are assigned to the
Drop Port.)
Single Flash Fail Failure of one of the unit’s two Flash Memory modules detected by the unit.
SEEPROM Failure Failure of SEEPROM hardware detected by the unit.
Netw Threshold Alarm Network Link Error Threshold (Data Frame Error Seconds) reached or exceeded.
DS0s must be assigned to the User Port.
User Threshold Alarm User Link Error Threshold (Data Frame Error Seconds) reached or exceeded. DS0s
must be assigned to the User Port.
Table A-13 System Test/Fault
Display Description
… 170 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Paradyne FrameSaver NP 110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Paradyne FrameSaver NP 110 in the language / languages: English as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info