458602

Paradyne FrameSaver NP 110 Manual

169
Zoom out
Zoom in
Previous page
1/175
Next page
Appendix
A-12 FrameSaver NP 110 User’s Manual - Installation Guide 980-001-0240B
November
2000
System
Test/Fault
System Test / Fault shows the highest priority System related test or fault currently de-
tected. This is displayed on the System View screen.
Table A-13 S
y
stem Test/Fault
Display Description
NVM Failure Failure of NVM (Non-Volatile Memory) detected by the unit and the latest
configuration may not have been saved.
Lp to User Loopback is in place at the User Port toward the User Circuit.
2047 to User 2047 pattern BERT is being sent toward the User Circuit.
LL Lp to User Loopback is in place at the User Port toward the User Circuit, in response to an LL
(Local Loopback) signal at the User Port interface (only if DS0s are assigned to the
User Port.)
LMI Netw Failure Invalid or no response to LMI Status enquiries toward Network. DS0s must be
assigned to the User Port.
LMI User Failure Invalid or no LMI Status requests from User equipment. DS0s must be assigned to
the User Port.
CSU Fault Failure of CSU related hardware detected by the unit.
Line Lp to Netw Full T1 Line loopback in place at Network Port toward Network Circuit.
Payld Lp to Netw Full T1 Payload loopback in place toward Network Circuit.
QRSS to Netw QRSS pattern BERT is being sent toward the Network Circuit.
Alt Ones to Netw Alternating Ones pattern BERT is being sent toward the Network Circuit.
2047 to Netw 2047 pattern BERT is being sent toward the Network Circuit.
Zero to Netw All Zeros pattern BERT is being sent toward the Network Circuit.
Line Lp to CPE Full T1 Line Loopback applied within the unit’s framer toward the CPE port(s):
User Port (also DSX Port and Drop Port if DSX/Drop Adapter installed.)
CSU CFA/Red Alarm Detected loss of T1 facility.
CSU Rmt/Yellow Alarm Carrier alarm notification that Transmit failure from this DCE has been detected on
this T1 facility.
CSU AIS/Blue Alarm Carrier alarm notification that an upstream signal failure has been detected on this T1
facility.
User Lp to Netw Loopback is in place at the User Port toward the Network Circuit.
User 2047 to Netw 2047 pattern BERT is being sent toward the Network Circuit (for DS0s assigned to
User Port).
User Zero to Netw All Zeros pattern BERT is being sent toward the Network Circuit (for DS0s assigned
to User Port).
… 169 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Paradyne FrameSaver NP 110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Paradyne FrameSaver NP 110 in the language / languages: English as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info