568673

Paradigm UltraCube 10 Manual

8
Zoom out
Zoom in
Previous page
1/20
Next page
q Auto-On/Standby or Auto-On/Off
If your subwoofer has this feature, it will turn on when it receives an
input signal—eliminating the need for a power switch. If no signal
is sensed for a period of time, the subwoofer will automatically switch
off (or switch to standby, depending on the model).
q Always-On
When the toggle switch is in the Always-On position, the subwoofer will
remain continuously “on.”
q Subwoofer Level
Balances the subwoofer output level to your speakers.
For instructions on setting the Subwoofer Controls once your subwoofer
has been connected refer to the section on “Fine Tuning,” page 8.
q Subwoofer Cut-Off Frequency and Bypass Option
(on models where applicable)
Controls the subwoofer’s upper-frequency cut-off. This can be set
to match the low-frequency roll-off characteristics of your front
speakers. For example, if your front speakers play to approximately 80
Hz, you can set the subwoofer cut-off frequency to 80 Hz.
Bypass Option allows you to bypass the subwoofer’s built-in cut-off
control to let your preamp/processor’s or receiver’s internal bass manage-
ment system provide the crossover function.
q Subwoofer/Satellite Phase Alignment
The sound from your subwoofer may arrive at the listening position out of
phase with the front speakers. This control synchronizes the subwoofer
and the front speakers through their frequency overlap region.
NOTE: For models without phase alignment controls, the (+) and (–)
connections can be reversed to change relative phase.
CONTROL FACILITIES
subwOOfer CONNeCTiON (continued)
Before connecting your subwoofer, please read this entire section
to determine which setup option best suits your needs. (See Dealer
if you require additional information.)
NOTE: Connection options vary by model. Review your check marks to
determine hook-up methods available.
1. Line-Level Input From Sub/LFE Output (Fig. 3) – For use with
a receiver, processor or subwoofer control unit that has a
Sub-Out/LFE-Out jack.
Using an RCA-to-RCA interconnect cable connect the subwoofer as
shown. If your subwoofer has two low-level input jacks use the right
(mono) input.
2. Speaker-Level Input (Fig. 4) – For use with a receiver or amplifier
that has no Sub-Out/LFE-Out or Pre-Out/Front-Out facilities.
Using high-quality speaker cable connect your subwoofer, as shown.
For convenience, you can also connect your front speakers to these
terminals (also shown in Fig. 4).
SUBWOOFER CONNECTION OPTIONS
On the rear of selected subwoofer models, allows for:
• Connection of optional Paradigm Perfect Bass Kit (PBK
™
);
• Future upgrades to the software installed in your subwoofer.
THE USB PORT
Even when the world’s finest speakers are perfectly positioned, the room
can still have a dramatic impact on performance. Room dimensions, dead
spots, archways, furniture placement and countless other factors can turn a
room into an additional instrument, playing alongside musicians or movie
scores with unwanted contributions of coloration and resonance.
Although the Control Facilities included on your Paradigm
®
subwoofer allow
you to fine tune for optimal bass performance in your room, Paradigm’s
Perfect Bass Kit (PBK
™
) (sold separately, see Dealer) allows you to correct
for the effects of your room’s boundaries.
PARADIGM’S PERFECT BASS KIT (PBK™)
7
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Paradigm UltraCube 10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Paradigm UltraCube 10 in the language / languages: French as an attachment in your email.

The manual is 0,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info