550986

Panasonic WV-SC384 Manual

208
Zoom out
Zoom in
Previous page
1/244
Next page
3. Configure [Wi-Fi Protected Setup (WPS)].
– Select “Allow” for “External registration”. (Default: Allow)
– Select “Use” for “WPS compliant (PIN method)”. (Default: Not use)
– Enter the wireless router's 8 digit PIN code in the “PIN code” field.
• Available number of characters: 8 characters
• Available characters: Numbers
• Default: None (blank)
Note
• When “Use” is selected for “WPS compliant (PIN method)”, settings cannot be performed
automatically using the WIRELESS button during start up for the PIN method.
4. Click the [Set] button.
→ A message asking you if you want to restart the camera is displayed. Click [OK]. Wait about 2 minutes
until the camera restarts.
5. Disconnect the LAN cable from the camera and reconnect the camera to the power outlet.
→ The camera will start about 90 seconds after connecting the power.
• After the camera is started, the WPS settings are only active for about 2 minutes. Therefore, perform
the settings in step 6 as quickly as possible (within 2 minutes).
6. Select ON for the WPS function (PIN code method) on the wireless router. (For more information, refer to
the operating instructions included with your wireless router.)
→ Settings between the wireless router and the camera will automatically start.
→ The WIRELESS button stops blinking orange and lights green. When the live indicator lights green,
the wireless settings have been successfully completed.
7. After the WIRELESS button lights green, start the “IP Setting Software” on the PC and access the camera.
• See page 222 for information on accessing the camera with the “IP Setting Software”.
• Confirm the status of the wireless connection on the [Status] tab of the “Wireless” page.
(®page 210)
Note
• If about 2 minutes pass after the WIRELESS button starts blinking and the wireless connection is not
completed, the WIRELESS button will blink red for about 10 seconds and then go off. If this happens
the wireless settings have failed. Check the wireless router's settings and connection procedures, and
then try performing the settings again.
• If the WPS settings fail to automatically configure, check the settings of the wireless router and the
camera.
• If you want to turn off the WIRELESS button’s and live indicator's green light, change the “Indicator”
settings on the [Basic] tab of the “Basic” page. (®page 55)
• When the WPS settings have successfully been automatically configured, “External registration” is
changed to “Not allow” from “Allow”.
Using a selected PIN code set to the camera
1. Connect the PC to the camera with a wired LAN connection and click the [Basic] tab on the “Wireless”
page.
208 Operating Instructions
18 Use the camera on a wireless LAN [Wireless] (SW174W only)
… 208 …


Need help? Post your question in this forum.

Forumrules
1

Forum

panasonic-wv-sc384

Reset search

  • What will happen when Viewnetcam service ends in March 2024? Submitted on 1-11-2023 at 06:38

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic WV-SC384 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic WV-SC384 in the language / languages: English as an attachment in your email.

The manual is 8,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic WV-SC384

Panasonic WV-SC384 User Manual - German - 248 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info