550986

Panasonic WV-SC384 Manual

207
Zoom out
Zoom in
Previous page
1/244
Next page
Performing settings automatically with the WIRELESS button (WPS
indicator)
Use the camera's WIRELESS button to automatically perform wireless settings.
1. Turn on the camera without connecting the LAN cable to enable the wireless settings.
→ After the initial pan/tilt operations are performed, the live indicator stops blinking orange and lights
orange. The live indicator lights orange and the camera starts up in wireless LAN mode about 90
seconds after the camera was turned on.
2. Select ON for the WPS function (Push-button method (PBC)) on the wireless router. (For more information,
refer to the operating instructions included with your wireless router.)
3. Press and hold down the WIRELESS button for a second or more until it blinks orange.
→ The camera and the wireless router automatically start performing wireless settings. Settings may take
up to 2 minutes to be performed.
→ When the automatic wireless settings have been successfully completed, the camera restarts about 5
seconds after the WIRELESS button stops blinking orange and lights green. The WIRELESS button
goes off, and after about 90 seconds lights green again when the wireless connection has been
successfully completed.
→ The wireless settings are updated.
4. After the WIRELESS button lights green, start the “IP Setting Software” on the PC and access the camera.
• See page 222 for information on accessing the camera with the “IP Setting Software”.
• Confirm the status of the wireless connection on the [Status] tab of the “Wireless” page.
(®page 210)
Note
• If about 2 minutes pass after the WIRELESS button starts blinking and the wireless connection is not
completed, the WIRELESS button will blink red for about 10 seconds and then go off. If this happens
the wireless settings have failed. Check the wireless router's settings and connection procedures, and
then try performing the settings again.
• If the WPS settings fail to automatically configure, check the settings of the wireless router and the
camera.
• If you want to turn off the WIRELESS button’s and live indicator's green light, change the “Indicator”
settings on the [Basic] tab of the “Basic” page. (®page 55)
• When the WPS settings have successfully been automatically configured, “External registration” is
changed to “Not allow” from “Allow”.
Performing settings automatically with PIN code settings
There are 2 methods for performing settings automatically with PIN code settings: using the PIN code preset
to the wireless router or using a selected PIN code set to the camera.
Using the PIN code configured to the wireless router
1. Check the preset 8 digit PIN code of the wireless router with a PC.
• For more information on how to check the preset PIN code of the wireless router, refer to the operating
instructions included with your wireless router.
• Depending on the wireless router used, the PIN code (default setting) may be written on a sticker
attached to the wireless router.
2. Connect the PC to the camera with a wired LAN connection and click the [Basic] tab on the “Wireless”
page.
Operating Instructions 207
18 Use the camera on a wireless LAN [Wireless] (SW174W only)
… 207 …


Need help? Post your question in this forum.

Forumrules
1

Forum

panasonic-wv-sc384

Reset search

  • What will happen when Viewnetcam service ends in March 2024? Submitted on 1-11-2023 at 06:38

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic WV-SC384 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic WV-SC384 in the language / languages: English as an attachment in your email.

The manual is 8,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic WV-SC384

Panasonic WV-SC384 User Manual - German - 248 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info