149172
31
Zoom out
Zoom in
Previous page
1/40
Next page
STR
TV/AV
SET UP
31
Your new TV is supplied with programme position 0’ set to receive an RF signal from your VCR, although a Scart c onnection is
preferable if the VCR is so equipped.
However, if for some reason yo ur VCR is tuned to a different RF channel then you will not receive any picture or so und from your VCR
on programme position ‘0’ of the TV. It will be necessary to either adjust the RF c hannel of your VCR (some VCR’s allow adjustment o f
their RF channel via their remote c ontrol unit) or to adjust the tuning of the TV’s programme position ‘0’ or both until it receives the RF
output channel of your VCR.
It is intended that this advice is used in conjunction with the instruction books for your additional equipment.
Use the AV1 Scart terminal for a VCR.
Use the AV2S Scart terminal fo r an S-- Video VCR.
Use the AV2S Scart terminal for a Q-- Link,
NEXT VIEWLINK or compatible VCR.
To tune your TV to the VCR
Switch on the VCR, insert and play a
pre -- recorded tape with known content
Open the Setup menu
Move to Tuning menu
Access Tuning menu
Move to Manual tuning
Access Manual tuning
Select programme position ‘0 VCR
Start searching for the VCR playback
of the known content tape
When the VCR playback is found,
press STR to store
Press the TV/AV button to exit
See below for installation of VCR and
Satellite
Receiver
Notes :
D If picture patterning occurs on programme position ‘0’ it
may be necessary to adjust the RF output channel o f
the VCR, refer to the VCR instruction book.
D If a Satellite Receiver and a VCR are going to be used
with RF cable connections it is important to avoid both
units being set on the same channel.
Refer to the Satellite Receiver and VCR instruction
books for pr ecise tuning information.
VCR AND SATELLITE RECEIVER INSTALLATION
Setup menu
Teletext FASTEXT
Off timer Off
Tuning menu Access
TV/AV
Select
Access
Exit
Manual tuning
21 68
VCR
CH32
Return --
Programme
down/up
Search
down/up
Exit
TV/AV
VCR
’STR’ Button Store
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic tx 28 pl 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic tx 28 pl 1 in the language / languages: English as an attachment in your email.

The manual is 3,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info