618650

Panasonic SCRT50 Manual

45
Zoom out
Zoom in
Previous page
1/52
Next page
45
RQT8655
Radio Page
Sound
Operation
Noise is heard.
Sound is distorted.
“TUNED” is flashing or doesn’t
light.
“ST” is flashing or doesn’t light
during FM broadcasts.
≥This is being caused by weak signal reception.
When listening to FM radio, try the following operations.
–Adjust the position of the FM antenna.
–Use an FM outdoor antenna.
–Press [FM MODE] to set to “MONO”.
When listening to AM radio, try the following operations.
–Adjust the position of the AM antenna.
–Press [FM MODE] to select between “BP1” and “BP4” that receives good reception.
—
34
34
—
34
A beat sound is heard. ≥Turn the television off or separate it from the unit. —
A low hum is heard during AM
broadcasts.
≥Separate the antenna from other cables and cords. —
The radio cannot be tuned in. ≥Turn off nearby televisions, video cassette recorders, satellite receivers and computers. —
All programmed radio presets
are erased.
Returns to the original setting
even after making changes to the
sound field system settings.
≥Radio and sound field system settings are stored to memory after pressing [Í]. Do not
remove the AC power supply cords until “BYE” disappears from the unit’s display.
—
No sound.
Low volume.
Distorted sound.
Cannot hear the desired audio
type.
≥Check the connections and settings.
≥Press [AUDIO] to select the audio.
≥Some multi-channel DVD-Audio will prevent down-mixing of all or part of their contents if this
is the manufacturer’s intention.
In the following situations, these DVD-Audio discs will not output audio correctly (Front two
channels only, etc. will output audio).
–When using headphones.
–When audio is output through the television speakers.
≥Turn the volume up.
≥Turn muting off.
≥Switch off the unit, determine and correct the cause, then switch the unit on.
Causes include:
–Shorting (bare wires touching) of positive and negative speaker wires.
–Using speakers with an impedance lower than that rated for this unit.
–Straining of the speakers through excessive volume or power.
–Using the unit in a hot environment without proper ventilation.
≥The factory settings for the “H. Bass” and Subwoofer levels are optimized for 5.1 channel
movie playback. If the bass seems too heavy during 2-channel disc playback, etc. change the
settings.
≥ When “R MUSICP” is selected, you cannot set anything other than “Equalizer (EQ)” or “H.
Bass” to change the sound quality. Also, when using headphones, you cannot set anything
other than “Equalizer (EQ)” or “Surround Music”.
≥If the audio is distorted when “F MUSICP” or “R MUSICP” is selected, turn the volume down
on the connected external device.
≥When audio playback is output through multi-channel, “Sound Field Control (SFC)” cannot be
set.
≥The sound effects will not work when audio is output from the HDMI AV OUT terminal.
≥Audio may not be heard when more than 4 devices are connected with HDMI cables. Reduce
the number of connected devices.
≥Depending on the connected equipment, the sound may be distorted if this unit is connected
with an HDMI cable.
2–11
(Setup Guide),
39
17
49
41
—
—
36
—
35, 36
—
41
—
—
—
—
Cannot switch audio. ≥You cannot change the audio type when DVD-R, DVD-R DL, DVD-RW (DVD-Video format),
+R, +R DL or +RW is in the disc tray.
≥You cannot change the audio type when playing DVD-R, DVD-R DL, DVD-RW (DVD-Video
format), +R, +R DL or +RW. [You can select “Main” or “SAP” in “Multi-channel TV Sound
(MTS)” in the Setup menu before recording.]
≥There are discs where audio cannot be changed because of how the disc was created.
—
39
—
Humming heard during play. ≥An AC power supply cord or fluorescent light is near the main unit. Keep other appliances
and cords away from the main unit.
—
Cannot operate the television. ≥Press [TV] to switch the remote control to operate the television.
≥
Change manufacturer code. Some televisions cannot be operated even if you change the code.
—
15
(Setup Guide)
The remote control doesn’t
work.
≥Press [THEATER] to switch the remote control to operate this unit.
≥The remote control and main unit are using different codes.
Change the code on the remote control.
Press and hold [ENTER] and the indicated number button at
the same time for more than 2 seconds.
≥The batteries are depleted. Replace them with new ones.
≥You are not pointing the remote control at the main unit’s remote control signal sensor during
operation.
≥Colored glass may obstruct the signal reception/transmission.
≥Don’t place the signal sensor in direct sunlight or in areas that may be subject to sunlight
exposure.
≥It may be necessary to set the code on the remote control again after changing the batteries.
≥It may be necessary to set the manufacturer code again after changing the batteries.
—
15
(Setup Guide)
4
4
—
—
15
(Setup Guide)
15
(Setup Guide)
Troubleshooting guide
RT-book.book Page 45 Monday, March 27, 2006 5:48 PM
… 45 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic SCRT50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic SCRT50 in the language / languages: English as an attachment in your email.

The manual is 7,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic SCRT50

Panasonic SCRT50 User Manual - English - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info