612856
20
Zoom out
Zoom in
Previous page
1/28
Next page
20
RQT9709
Occasionally, Panasonic may release updated
software for this unit that may add or improve the way
a feature operates. These updates are available free of
charge.
Preparation
Connect this unit to the wireless network. (> 11)
Make sure that the wireless network is connected to the
Internet.
1 Press [SETUP] repeatedly to select
“SW UPDATE” and then press [OK].
2 Press [3, 4] to select “UPDATE? Y” and then
press [OK] to start the update.
{. After the update has finished, “SUCCESS” is displayed.
3 Disconnect the AC mains lead and reconnect it
after 3 minutes.
DO NOT DISCONNECT the AC mains lead while one of
the following messages is displayed.
“LINKING”, “UPDATING” or “%”
(“ ” stands for a number.)
If you do not want to update the unit, select “UPDATE? N”
and then press [OK] in step 2.
If there are no updates, “NO NEED” is displayed after step 2.
During the update process, no other operations can be
performed.
Downloading will require several minutes. It may take
longer or may not work properly depending on the
connection environment.
Checking the software version
1 Press [SETUP] repeatedly to select “SW VER.” and then
press [OK].
{. The version of the installed software is displayed.
2 Press [OK] to exit.
To check the Wi-Fi
®
signal strength where the unit is
located.
Preparation
Connect this unit to the wireless network. (> 11)
1 Press [SETUP] repeatedly to select “SIG.LEVEL”
and then press [OK].
The unit’s display shows “LEVEL ”.
(“ ” stands for a number.)
2 Press [OK] to exit this display mode.
It is recommended to have a signal strength of “3”. Change
the position or angle of your wireless network router or the
unit if the indication is “2” or “1” and see if the connection
improves.
If “LEVEL 0” is displayed, this unit cannot establish a link with
the wireless network router. (> 22)
This function does not work when AirPlay is used.
This unit can turn on automatically from standby mode
when this unit is selected as the AirPlay speakers.
Preparation
Connect this unit to the wireless network. (> 11)
1 Press [SETUP] repeatedly to select “NET STNBY”
and then press [OK].
2 Press [3, 4] to select “ON” and then press [OK].
To cancel this function, select “OFF” in step 2.
The factory preset is “OFF”. If this function is set to “ON” the
standby power consumption will increase.
To check the unit’s IP/MAC address.
1 Press [CD] to select “CD”.
2 Press and hold [s WPS] on the unit and [4] on
the remote control until the unit’s display shows
the IP address.
{. The IP address is partially displayed.
To display the MAC address on the unit, repeat the
steps above by replacing [4] with [3].
3 Press [3, 4] on the remote control to show the
rest of the IP address.
Be sure to remove the disc from the disc tray when checking
the address.
The “ – ” displayed on the top or bottom left of the display
indicate the first and last units respectively.
Software update
Wi-Fi
®
signal strength
Network standby
IP/MAC Address
SC-HC57DB~RQT9709-1B.book Page 20 Friday, March 2, 2012 3:31 PM
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic SCHC57DBEB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic SCHC57DBEB in the language / languages: English as an attachment in your email.

The manual is 4,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info