452164
48
Zoom out
Zoom in
Previous page
1/52
Next page
48
VQT3M52
Messages
The following messages or service numbers appear on the
television or unit’s display when something unusual is detected
during startup and use.
Cannot play.
You inserted an incompatible disc.
Cannot play on this unit.
You tried to play a non-compatible image.
No disc inserted.
The disc may be upside down.
$ This operation is not available.
Some operations are unsupported by the unit. For example;
jBD-Video: During playback, reverse slow-motion or
reverse frame-by-frame is not possible.
IP address is not set.
The “IP Address” in “IP Address / DNS Settings” is “---. ---.
---. ---”. Set the “IP Address”, “Subnet Mask”, and “Gateway
Address”. (Select the automatic address acquisition if
necessary.)
[BTT362]
The wireless access point currently has a low network
security setting. It is recommended to change to a higher
setting.
Authentication type for the Wireless LAN is set to “Open
system”, or the encryption type is set to “No encryption”. It is
recommended to encrypt for safety reasons. For details,
refer to the instructions of the Wireless router being used.
Encryption is required when playing back video, etc., from
DLNA compatible devices.
No Video
Depending on the connected iPod/iPhone, video menu may
not be available on the TV. Select “ALL” on the unit’s display
and operate video playback from your iPod/iPhone menu.
(> 35)
F99
The unit fails to operate properly. Press [Í/I] on the main
unit to switch the unit to standby for 3 seconds. Now press
[Í/I] on the main unit again to turn the unit on.
U59
The unit is hot.
The unit switches to standby for safety reasons. Wait for
about 30 minutes until the message disappears.
Select a position with good ventilation when installing the
unit. Do not block the ventilation hole on the rear and side of
the unit.
HDMI ONLY
Some BD-Video discs can only be output with HDMI.
NET
While connecting to a network.
No PLAY
There is a viewing restriction on a BD-Video or DVD-Video.
(> 40)
No READ
The media is dirty or badly scratched. The unit cannot play.
PLEASE WAIT
The unit is carrying out internal process. This is not a
malfunction. You cannot operate the unit while “PLEASE
WAIT” is displayed.
REMOVE
The USB device is drawing too much power. Remove the
USB device.
SET
(“ ” stands for a number.)
The remote control and main unit are using different codes.
Change the code on the remote control.
Press and hold [OK] and the indicated
number button at the same time for
more than 5 seconds.
H or F
(“ ” stands for a number.)
Check and correct the speaker cable connections.
There is something unusual.
Check the unit using the troubleshooting guide. If the service
number does not disappear, do the following.
1 Disconnect the plug from the household mains socket, wait
a few seconds, then reconnect it.
2 Press [Í/I] to turn the unit on.
If the service number does not disappear despite doing the
above, request service from the dealer. Inform the dealer of
the service number when requesting service.
UPD/
(“ ” stands for a number.)
The firmware is being updated.
Please do not turn off the unit.
IPOD OVER CURRENT ERROR
The iPod/iPhone is drawing too much power. Remove the
iPod/iPhone, and turn the unit off and on again.
START
The system is being restarted during the firmware update.
Please do not turn off the unit
FINISH
The firmware update is completed.
NOT CONDITIONAL
The requested operation cannot be conducted.
On the television
On the unit’s display
SCBTT362_262_EB_VQT3M52_eng.book 48 ページ 2011年1月25日 火曜日 午後8時22分
48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic SC-BTT362 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic SC-BTT362 in the language / languages: English as an attachment in your email.

The manual is 2,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic SC-BTT362

Panasonic SC-BTT362 User Manual - German - 52 pages

Panasonic SC-BTT362 User Manual - Dutch, Spanish - 104 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info