511534
103
Zoom out
Zoom in
Previous page
1/179
Next page
[PROJECTOR SETUP] menu
ENGLISH - 103
Settings
10)
Press

to select [CALIBRATION
TIME].
11)
Press the <ENTER> button.
12)
Enter the time and press the <ENTER>
button
z
Measure brightness at a specied time.
Dynamic iris is xed to open during
measurement.
13)
Press

to select [CALIBRATION
MESSAGE].
14)
Press
󱚣󱚤
to switch [CALIBRATION
MESSAGE].
z
The setting will change as follows each time
you press the button.
[ON] [OFF]
[ON]
Displays a message during
calibration.
[OFF]
Does not display a message during
calibration.
15)
Press

to select [APPLY].
16)
Press the <ENTER> button.
z
The set [MODE] and [LINK] are enabled, and
LAMP RELAY screen alert is displayed when
the [LAMP RELAY] setting is [OFF]. When
[CALIBRATION MESSAGE] is set to [ON], a
calibration running message is displayed which
will automatically disappear 30 seconds after
calibration completes.
z
If the [MODE] in [BRIGHTNESS CONTROL
SETUP] is not [OFF] when the <ENTER>
button is pressed, the lamp brightness at that
time is recorded as the standard brightness.
z
If the <ENTER> button is pressed when [LINK]
is [GROUP A] to [GROUP D], the group name
is displayed on the projector screen set as the
same group.
/,1. *5283$
Note
z
When setting the [MODE] in [BRIGHTNESS
CONTROL SETUP] to [AUTO] or [PC], [APPLY]
luminance control after the shutter is open for at
least two minutes.
z
If the shutter is closed within approx. 10 minutes
from the time that the lamp turns on when operating
with the [MODE] in [BRIGHTNESS CONTROL
SETUP] set to [AUTO] or [PC], brightness may be
corrected approx. two minutes after the shutter
opens because brightness could not be measured.
z
When operating with the [MODE] in [BRIGHTNESS
CONTROL SETUP] set to [AUTO] or [PC], lamp
brightness is automatically measured eight minutes
after a lamp is turned on, and corrected to the same
value as the screen brightness and the standard
brightness at the time of [APPLY]. Lamp brightness
cannot be measured during the eight minutes after
it is turned on because it is not steady.
z
When [LAMP SELECT] is 2 lit or higher and the
[MODE] in [BRIGHTNESS CONTROL SETUP] is
operating in [AUTO] and a light fails to turn on or
LAMP RELAY is performed, brightness is corrected
one minute later whenever possible.
z
When operating with [MODE] in [BRIGHTNESS
CONTROL SETUP] set to [AUTO], and [LINK] is
[OFF], brightness correction is performed until
correction exceeds the maximum correction
amount.
z
In certain projector environments, dust may
accumulate on the lens or screen or inside the
projector and increase variation in brightness.
z
Adjust luminance control again when lamp
degradation causes increased variation in
brightness or a lamp is replaced.
z
For continued use longer than 24 hours, set
the [BRIGHTNESS CONTROL SETUP] to
[CALIBRATION TIME], or set [LAMP RELAY]
(
page 101). Correction is not automatically
executed when not set.
z
Luminance control and iris operate simultaneously,
but the iris does not operate when fully open while
a brightness measurement is performed.
z
The setting of [CALIBRATION TIME] applies at the
time when the time is entered.
z
The setting of [CALIBRATION MESSAGE] applies
at the time when the item is switched with
󱚣󱚤
.
103


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic PT-DZ21KE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic PT-DZ21KE in the language / languages: English as an attachment in your email.

The manual is 17,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic PT-DZ21KE

Panasonic PT-DZ21KE User Manual - German - 190 pages

Panasonic PT-DZ21KE User Manual - German - 190 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info