598890
82
Zoom out
Zoom in
Previous page
1/129
Next page
PROJECTOR SETUP menu
82
- ENGLISH
Settings
Press ▲▼ to select [TIME] or 4 )
[COMMAND] and change the setting
according to the instructions of the
menu.
TIME
Set the time at which the command
will be executed using ▲▼ or numeral
buttons.
COMMAND
Select a command to execute at the
set time from the following.
POWER ON
STANDBY
SHUTTER
OPEN
SHUTTER
CLOSE
INPUT RGB1
INPUT RGB2
INPUT VIDEO
INPUT S-VIDEO
INPUT DVI-D
INPUT HDMI
INPUT SDI
Û
LAMP POWER
HIGH
LAMP POWER
LOW
LAMP DUAL
LAMP SINGLE
P IN P OFF
P IN P USER1
P IN P USER2
P IN P USER3
PT-DZ8700U/PT-DS8500U only:
Û
Press ▲▼ to select [STORE] and 5 )
press <ENTER> button.
Note
If you try to register a setting that would cause the
z
lamp to ash for a short time, an error message will be
displayed on the screen. Set the [TIME] and [COMMAND]
again.
To delete a command which has been set, press
z
<DEFAULT> button.
If multiple commands have been set for the same time,
z
they are executed in chronological order starting from the
smallest command number.
The setting time operates under the local time.
z
(
Æ
page 84)
If an operation is executed with the remote control or
z
control panel of the projector or with a control command
before the command set in the schedule is executed, the
command set with this function may not be executed.
RS-232C
This sets the communication parameters at the serial
terminals.
Press ▲▼ to select [RS-232C].1 )
Press <ENTER> button.2 )
The [
z
RS-232C] screen will be displayed.
Press ▲▼ to select communication 3 )
conditions.
press ◄► to change the setting.4 )
Note
Refer to “Serial terminal” (
z
Æ
page 117).
J
Selecting items in [EMULATE]
When using the control commands for one of our
projectors that you have previously purchased to
control this projector using a computer via its serial
input terminal, set up the EMULATE function as
follows. This will allow you to use the control software
etc. designed for our existing projectors.
Select [EMULATE] in step 3).1.
Press <ENTER> button.2.
Press ▲▼ to select the required item.3.
Press <ENTER> button.4.
DEFAULT
DZ8700U Series, DS8500U Series,
DW8300U Series,
D5000 Series,
D6000 Series, DW6300
Series,
DZ6700
Series, DZ6710 Series
D9610
SERIES
D9510 Series, D9610 Series,
D9500 Series, D9600 Series,
D8500 Series, D8600 Series
D7700
SERIES
D7500 Series, D7600 Series,
D7700 Series, DW7000 Series
L6500
SERIES
L6500 Series, L6510 Series,
L6600 Series
J
About [EMULATE SETTING]
This sets which input signal can be selected using the
input signal change command when a projector of a
specic model is used with the emulate function.
Select [EMULATE SETTING] in step 3).1.
Press <ENTER> button.2.
The [EMULATE SETTING] screen will be
z
displayed.
When the D9610 Series is selected
Q
Press ▲▼ to select input signal 1.
[VIDEO], [S-VIDEO], [RGB1], [DVI-D] or
[SDI].
[RGB2] and [HDMI] cannot be selected.
z
[SDI] is not shown for PT-DW8300U.
z
Press ◄► to select the input signal 2.
change command to be assigned to
the selected input signal.
Selectable input signal change commands
z
When RGB1 is selected:
[INPUT1], [INPUT2], [INPUT3], [INPUT
RGB], [NONE]
For all other instances:
[INPUT1], [INPUT2], [INPUT3], [NONE]
The same input signal change command
z
cannot be assigned to multiple input signals.
82


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic PT-DS8500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic PT-DS8500 in the language / languages: English as an attachment in your email.

The manual is 12,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info