598890
81
Zoom out
Zoom in
Previous page
1/129
Next page
PROJECTOR SETUP menu
ENGLISH -
81
Settings
Display the internal test pattern [ALL 9 )
WHITE] on all projectors.
Set [BRIGHTNESS CONTROL GAIN] 10)
of all projectors to 100 %.
Set [BRIGHTNESS CONTROL GAIN] 11)
of the darkest projector to 90 %.
Adjust [BRIGHTNESS CONTROL 12)
GAIN] of the other projectors to that
of the projector that was set to 90 %.
Set [MODE] of [BRIGHTNESS 13)
CONTROL SETUP] of all projectors to
[AUTO] and set [LINK] to [GROUP A].
[APPLY] [BRIGHTNESS CONTROL 14)
SETUP] of all projectors and press
<ENTER> button.
Brightness control will commence.
z
Note
The brightness is corrected automatically each time the
z
lamps are turned on using the power switch etc.
If the brightness uctuates signicantly or the lamp has
z
been replaced, re-adjust the brightness control.
STANDBY MODE
You can select the electrical consumption while in
standby mode.
Press ▲▼ to select [STANDBY MODE].1 )
Press ◄► to switch [STANDBY 2 )
MODE].
The setting will change as follows each time
z
◄► is pressed.
NORMAL ECO
Note
With [ECO] setting, NETWORK function, RS-232C output
z
and some of RS-232C commands are not available.
When switch on the projector, projection will start about
10 seconds late.
SCHEDULE
This sets the command execution schedule for each
day of the week.
J
How to enable the SCHEDULE
function
Press ▲▼ to select [SCHEDULE].1 )
Press ◄► to switch [SCHEDULE].2 )
The setting will change as follows each time
z
◄► is pressed.
ON OFF
Note
If [SCHEDULE] is set to [ON], the setting for [STANDBY
z
MODE] is automatically set to [NORMAL] and cannot be
changed. Even if [SCHEDULE] is then set to [OFF] when
in this state, the setting of [STANDBY MODE] remains at
[NORMAL].
J
How to assign a program
With [SCHEDULE] switched to [ON], 1 )
press <ENTER> button.
The [SCHEDULE] screen will be displayed.
z
Select and assign program to each day 2 )
of week.
Press ▲▼ to select a day of week and press
z
◄► to select a program number.
You can set the program from No.1 to No.7.
z
“- - -” indicates that the program number has
not been set yet.
J
How to set a program
You can set up to 16 commands to each program.
On the [SCHEDULE] screen, press ▲1 )
to select [PROGRAM EDIT].
Press ◄► to select a program number 2 )
to be set and press <ENTER> button.
Press ▲▼ to select a command 3 )
number and press <ENTER> button.
You can change the page using ◄►.
z
81


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic PT-DS8500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic PT-DS8500 in the language / languages: English as an attachment in your email.

The manual is 12,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info