627468
8
Zoom out
Zoom in
Previous page
1/40
Next page
Before
Use
-42-
ª
Using the Remote Controller
1
Direct the Remote Controller to the
Remote Control Sensor
(3)
of the Movie
Camera and press an appropriate button.
Distance from the Movie Camera: Within
approximately 5 metres
Angle: Within approximately 15o in the
vertical and horizontal directions from the
central axis
The above operative ranges are for indoor
use. Outdoors or under strong light, the Movie
Camera may not operate properly even within
the above ranges.
Within a 1-metre range, you can also use the
Remote Controller on the LCD Monitor side of
the Movie Camera.
Selecting Remote Controller Modes
When 2 Movie Cameras are used
simultaneously, they can be operated
individually by selecting different Remote
Controller Modes.
If the Remote Controller Mode of the Movie
Camera and that of the Remote Controller do
not match, [REMOTE] Indication is displayed.
Setup on the Movie Camera:
Set [REMOTE] on the [OTHER FUNCTIONS]
Sub-Menu to the desired Remote Controller
Mode. (
-45-
)
Setup on the Remote Controller:
[VCR1]:
Press the [D] Button and [] Button
simultaneously. 1
[VCR2]:
Press the [E] Button and [] Button
simultaneously. 2
When the battery in the Remote Controller is
replaced, the mode is automatically reset to
[VCR1] Mode.
Power Supply
ª
Using the AC Adaptor
1 Connect the AC Mains Lead to the AC
Adaptor and the AC mains socket.
15˚
15˚
15˚
15˚
(3)
INDEX INDEX
SELECT
STOP
KL
STILL ADV
T
W
PAU SE
STILL ADV
61 5
;
ED
21
DC IN 7.9V
1
(37)
The AC Mains Leads outlet plug does not fit
entirely into the AC Adaptor socket. A gap
will remain as shown 1.
2
Connect the DC Input Lead to the [DC IN]
Socket
(37)
on the Movie Camera.
3
Connect the DC Input Lead to the AC
Adaptor.
Before connecting or disconnecting the
power supply, set the [OFF/ON] Switch on
the Movie Camera to [OFF] and make sure
that [CAMERA/VCR] Lamps is not lit.
ª
Using the Battery
Before use, fully charge the Battery.
1
Attach the Battery to the AC Adaptor and
charge it.
Since the Battery will not be charged when
the DC Input Lead is connected to the AC
Adaptor, disconnect it from the AC Adaptor.
The [POWER] Lamp and [CHARGE] Lamp
lights up, and charging starts.
When the [CHARGE] Lamp goes off,
charging is completed.
2
Attach the charged Battery to the Movie
Camera.
Disconnecting the Power Source
Set the [OFF/ON] Switch
(50)
to [OFF] and,
disconnect the DC Input Lead or while pressing
the [PUSH] Button
(35)
, slide the Battery
upward to disconnect it.
ª
Using the Car Battery Charger
If you use the Car Battery Charger (VW-KBD2E;
optional), you can supply power to the Movie
Camera and charge the battery inside your car.
For further information, refer to the instruction
manual of the Car Battery Charger.
Be sure to start the car engine before you
connect the Car Battery Charger, otherwise the
fuse may blow.
For other notes concerning this item, see
-64-
.
PUSH
OFF ON
(35)
(50)
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic NVMD9000EN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic NVMD9000EN in the language / languages: English as an attachment in your email.

The manual is 3,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info