627468
7
Zoom out
Zoom in
Previous page
1/40
Next page
Before
Use
-41-
ª
Attaching the Microphone to the
Movie Camera
1
Attach the microphone to the Movie
Camera shoe.
1) Loosen the Shoe Lock.
2) Attach the microphone.
3) Firmily tighten the Shoe Lock.
2
Connect the Stereo Mini-Plug Cord to the
[EXT MIC]
(28)
socket.
You can adjust the microphone angle within
the range shown in the figure.
Hold the Shoe Lock portion when attaching
and removing the microphone.
Be sure to set the Movie Camera power to
[OFF] before connecting the microphone.
ª
Using the External Stereo
Microphone
1
Set the [OFF/MONO/STEREO] Switch
(53)
to [MONO] or [STEREO].
[OFF]: Turn off the microphone power.
[MONO]: Records sound in front of the
movie camera in monaural.
[STEREO]: Records sound in a wide area in
stereo.
Although you can change the setting of the
[OFF/MONO/STEREO] Switch while
recording, the sound of the switch being
changed may be recorded. Pause your
recording before changing the setting of this
switch.
When the [OFF/MONO/STEREO] Switch is
changed from [OFF] to [MONO] or [STEREO],
the [BATTERY] Lamp
(54)
will light temporarily
if there is still plenty of power in the battery. If
the [BATTERY] Lamp does not light
temporarily, replace the battery with a new
one.
1)
2)
3)
EXT MIC
(28)
OFF
STEREO
MONO
BATTERY
OFF ON
WIND CUT
(53) (54)
(55)
Changing the [WIND CUT OFF/ON] Switch
The microphone is equipped with a wind shield
that is designed to cut down wind noise, but
when the wind is so strong that even the wind
shield is not adequate to keep down the noise,
set the [WIND CUT OFF/ON] Switch
(55)
to
[ON] to further reduce the wind noise.
[OFF]: The microphone should usually be used
with this position.
[ON]: Set the [WIND CUT OFF/ON] Switch to
this position to reduce wind noise or
bass noise.
Although you can change the setting of the
[WIND CUT OFF/ON] Switch while recording,
the sound of the switch being changed may be
recorded. Pause your recording before
changing the setting of this switch.
For other notes concerning this item, see
-68-
.
The Remote Controller
ª
Inserting a Button-type Battery
Before using the Remote Controller, insert the
supplied button-type battery.
1
While pressing the Stopper 1, pull out the
Battery Holder.
2
Insert the button-type battery with the (i)
marking facing upward.
3
Insert the Battery Holder into the Remote
Controller.
When the button-type battery is exhausted,
replace it with a new CR2025 battery. (A
battery is normally expected to last about
1 year. However, it depends on operation
frequency.)
Make sure to match the poles correctly when
inserting the battery.
CAUTION
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type recommended by the equipment
manufacturer. Discard used batteries according
to manufacturers instructions.
WARNING
Risk of fire, explosion and burns. Do not
recharge, disassemble, heat above 100xC or
incinerate. Keep the Button-Type battery out of
the reach of children. Never put Button-Type
battery in mouth. If swallowed call your doctor.
1
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic NVMD9000EN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic NVMD9000EN in the language / languages: English as an attachment in your email.

The manual is 3,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info