Manual Panasonic nv fj730 eg s (page 22 of 30) (English)

136256

Zoom out

Zoom in

1/30

G-CODE Programming

Programming is now easier than ever; simply enter the

G-

CODE number found in the programme scheduling pages of

newspapers and magazines.

G-

CODE numbers are numbers assigned to programmes listed

in the TV programme schedule found in newspapers and TV

guides. When these numbers are entered, the numbers are

converted to actual programming.

G-

CODE is a registered trademark of Gemstar

Development Corporation. The G-

CODE system is

manufactured under license from Gemstar Development

Corporation.

Preparations

– Confirm that the VCR is on.

– Confirm that the TV is on and the VCR viewing channel is

selected.

– Insert a video cassette with an intact erasure prevention

tab.

– Set the VCR/TV switch E to [VCR].

– Check that the clock is set to the correct time. If it has not

been set, refer to page 10.

Example:

Programming a timer recording of a TV programme with the

G-

CODE number 123456

4 Press the Cursor button (1) S to select the Category.

Then, select the desired category by pressing the

Cursor buttons (3421) S.

– Alternatively, you can set the category on the Navigator

list. (See page 23 for details.)

– This function is activated when [JET NAVIGATOR] is

set to [ON]. (See page 13.) When [JET NAVIGATOR] is

set to [OFF], procced to the step 6.

5 Press the MENU button U to

make the previous display

appear.

6 Press the TIMER (REC) button A to switch the VCR

over to the timer recording standby mode.

– When [JET NAVIGATOR] is set to [ON], the

[PROGRAMME IS COMPLETE. REMAINING

PROGRAMME 49.] message appers. (See page 13.)

– When [JET NAVIGATOR] is set to [OFF], the

[PROGRAMME IS COMPLETE.] message appears.

(See page 13.)

– Check that [Á] is lit on the VCR display.

If it is flashing, check the timer recording details again.

(See page 21.)

Notes:

– When the G-

CODE number is used for programming, the

recording time may be slightly longer than the actual

programme time.

– Repeat steps 2 and 3 if [PROGRAMME IS INCOMPLETE.]

appears.

– When programming two or more programmes, repeat steps

1–6.

– The procedures for checking and cancelling a timer

programme are the same as on page 21.

To Suspend the Timer Recording Standby

Mode

See page 20.

SP ON SP OFF

CHDATE ON OFF

SP2 13:45 14:1527SA

CATEGORY :

CHDATE ON OFF

SP–– 13:45 14:1527SA

CATEGORY :

END:G-CODE

---------

G-CODE

SET :OK

END:G-CODE

PROGRAMME

123456

---

G-CODE

END : MENU

CATEGORY SETTING

≥MOVIE

≥MUSIC

≥DRAMA

≥EDUCA

≥DOCUM

≥SPORT

≥CHILD

≥NEWS

≥OTHER

≥

–––––

END : MENU

CATEGORY SETTING

≥MOVIE

≥MUSIC

≥DRAMA

≥EDUCA

≥DOCUM

≥SPORT

≥CHILD

≥NEWS

≥OTHER

≥

–––––

CHDATE ON OFF

SP2 13:45 14:1527SA

CHECK

: PROG./CHECK

On Screen Display

Operations

1 Press the G-CODE button K to

display the menu for entering the

G-

CODE number on the TV.

2 Press the Numeric buttons 2 to

enter the G-

CODE number.

– It is also possible to check the

number with VCR display without

appearing the On Screen Display.

– If you have entered the wrong number, press the

CANCEL button ; then enter the proper number. An

alternative method is to press the Cursor button (2) S

and then enter the proper number.

3 Press the OK button T.

– The entered programme appears

on the display.

– The starting time and the ending

time appears alternately each

5 seconds on the VCR display.

– Confirm that the number

corresponds to the right

programme. If the display looks

like this and Á on the VCR

display flashes on and off: select

the desired programme position

using the CH button :, then

press the OK button T.

– To make any corrections, use the DATE button 9, the

ON button D, the OFF button C and the SPEED button

B the same way as described on page 20.

VCR display

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic nv fj730 eg s in the language / languages: English as an attachment in your email.

The manual is 1,08 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Panasonic nv fj730 eg s Manual

Product: