502434
12
Zoom out
Zoom in
Previous page
1/168
Next page
-
12
-
Display
Battery indication lamp
3. Press the and buttons to set the
desired time.
Buttons Display Seconds
30 3
1 0.1
0 Off
4.
Press the OK button to accept the selected
setting.
The control panel will stop flashing and
light up, and the torque clutch setting
will be displayed.
CAUTION:
Be sure to verify the new value after
changing the setting.
Initializing All Settings
Factory settings
Torque clutch setting: “F” (torque con-
trol function off)
Interval setting: 0 (off)
This section explains how to revert all tool
settings to their default values at the time of
shipment from the factory.
The error display will be turned off.
1. Set the tool to configuration mode.
(See page 10.)
2. Press the format button.
The control panel will begin flashing.
Display: The letter “F” ashes on and off.
Battery indication lamp: The upper and
lower bars of the battery ash on and off.
Display
Battery indication lamp
3. Press the OK button to accept the select-
ed setting.
The control panel will stop flashing and
light up.
Checking Tool Settings
This section describes how to have the tool
display current settings for approximately 3
seconds when the tool is stopped.
You cannot check tool settings when the
control panel is turned off. First, engage
the switch briefly to reactivate the display.
Checking the torque clutch setting
1.
Press the torque set button.
Control panel display
Display: The torque set lights up.
Battery indication lamp: The upper bar of
the battery ashes on and off.
Checking the interval
1.
Press the interval set button.
Control panel display
Display: The interval set lights up.
Battery indication lamp: The middle bar
of the battery ashes on and off.
Checking tool circuits
1.
Press the torque set button.
Control panel display
Display: The torque set display lights up.
Battery indication lamp: The middle and
lower bars of the battery ash on and off.
Display Tool circuit
H2 EYFLA1
H3 EYFLA
2
H4 EYFLA3
NOTE:
If you engage the switch while a setting
is being displayed, the control panel will
revert to the torque clutch setting dis-
play.
CAUTION:
The torque set display is not intended
to be used to identify the type of drive
component parts (hammer, etc.) used
in a particular tool.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic EYFLA1A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic EYFLA1A in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 17,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info