Manual Panasonic EY7430 (page 10 of 200) (English, German, Dutch, Danish, French, Italian, Swedish, Turkish, Spanish, Norwegian, Finnish)

568597

Zoom out

Zoom in

1/200

parts away from the chuck and

any shavings. There is a risk of

injury resulting from being hit by

shavings or a broken or detached

drill bits. Replace all drill bits

regularly.

• Please interrupt the operation

when the body heats up, and after

let it cool down to the adequate

temperature before restarting.

NOTE

• Do not attempt to remove a screw

that is rusty or stuck using a box

driver (M6 or higher).

NOTE for

EY7430

When drilling holes in metal

• Reduce pressure slightly just before

drilling through to the other side.

When drilling a hole more than 8mm

in diameter, start by drilling with

smaller bits and expand the hole with

larger bits until you reach the desired

diameter. If it encounters too much

resistance, the tool will lock or the bit

will slip inside the chuck.

• If the drill slips, remove and re-insert

the drill bit, then fasten the chuck

securely. Next, continue drilling, putting

only light pressure on the tool. When

drilling through metal, pressing hard

does not necessarily ensure that the

job will be done faster.

• Apply machine oil to the drill point to

make the job go more smoothly.

• Do not strain the motor.

• When the tool becomes very hot, stop

working temporarily and let it cool

down to avoid damaging it.

NOTE for

EY7530

• Do not use for drilling holes in metal.

Under high torque, drill bits for metal

can chip and cause injury.

CAUTION:

If the collar does not return to its original

position or the bit comes out when

pulled on, the bit has not been properly

attached. Make sure the bit is properly

attached before use.

Use 6.35 mm hexagonal bits.

To ensure proper securement of the bit, use

only hexagonal bits with 9.5 mm detent.

6.35 mm

9.5 mm

Model No: EY7430 & EY7530

III. OPERATION

[Main Body]

CAUTION:

• When operating the tool by

pulling the trigger, there may be

a momentary lag before rotation

starts. This does not signal a

malfunction.

* This lag occurs as the tool’s

circuitry starts up when the

trigger is pulled for the first time

after installing a new battery

pack or after the tool has not

been used for at least 1 minute.

Rotation will start without any lag

during second and subsequent

operations.

• To prevent excessive temperature

increase of the tool surface, do

not operate the tool continuously

using two or more battery packs.

The tool needs cool-off time before

switching to another pack.

• Do not close up vent holes on the

sides of the body during operation.

Otherwise, the machine function

is adversely affected to cause a

failure.

• Do NOT strain the tool (motor).

This may cause damage to the

unit.

• Do not strain the motor.

• Use the tool in such a way as to

prevent the air from the body vent

holes from blowing directly onto

your skin. Otherwise, you may get

burned.

• During operation, keep all body

EY7530_7430_3732_0L32_02(Eng).indd 10 2014/08/18 15:40:52

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic EY7430 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,16 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Panasonic EY7430 Manual

Product: