386557
8
Zoom out
Zoom in
Previous page
1/88
Next page
8
Using Keyless drill chuck
(EY9X003E)
CAUTION: Use keyless drill chuck ONLY in
Drill Driver Mode of EY6535.
This chuck is not designed to be
used in IMPACT MODE.
It can be damaged and its life will
be reduced. Moreover, the chuck
and its metal parts, such as the
push button, front parts, and bit
may become very hot. To prevent
skin burns, use work gloves and/or
allow heated parts to cool down
before handling.
Make sure the work environment is
safe. When retracting drill from
work material, Keyless drill chuck
may detach if subjected to 100kg
or more of pull force. Detachment
will be sudden. Use care and avoid
excessive force when retracting
drill from work material.
1. Attaching Keyless drill chuck (Fig. 2)
Attach the chuck by sliding the female detent
on the bottom of the chuck to the square drive
on the body.
Make sure the chuck is firmly connected to the
body
2. Inserting the bit (Fig. 3)
Insert the bit, and turn the lock collar clock-
wise(looking from the front) holding the sleeve
until jaws close firmly.
3. Removing the bit (Fig. 4)
Turn the lock collar counterclockwise (looking
from the front).
Then remove the bit.
CAUTION: If the drill bit becomes too tight to
remove, hold two lock collars with
pipe wrenches and turn them in
opposite directions. (Fig. 5)
4. Detaching Keyless drill chuck (Fig. 6)
To detach the chuck, PUSH the button to
release the chuck from the square drive.
CAUTION: Drill bit blade is sharp. Make sure to
remove the drill bit before you set
and detach the keyless drill chuck.
Using Quick change chuck
(EY9HX110E)
This Quick change chuck is
designed to be used with Pana-
sonic EY6535.
Top collar : To insert or to
remove bit
Bottom collar : To attach or to
detach Quick
change chuck
Use 6.35 mm (1/4") hexagonal bits.
To ensure proper securement of the bit, use only
hexagonal bits with 9.25 mm (3/8") detent. (Fig. 7)
CAUTION: Make sure the work environment is
safe. When retracting bit from work
material, Quick change chuck may
detach if subjected to 50kg or more
of pull force. Detachment will be sud-
den. Use care and avoid excessive
force when retracting bit from work
material.
1. Attaching Quick change chuck
Attach the Quick change chuck by pulling the
bottom collar forward and sliding the female
detent on the bottom of the chuck to the
square drive on the body.
Release the bottom collar to make sure the
Quick change chuck is firmly connected to the
body.
2. Inserting the bit (Fig. 8)
Pull the top collar of the Quick change chuck
forward, then insert the bit.
Release the bottom collar to make sure the bit
is firmly connected to the chuck.
3. Removing the bit (Fig. 9)
Pull the top collar of the Quick change chuck
forward, then pull the bit.
CAUTION: lmpact mechanism creates heat.
Square drive and accessory may
become very hot and may cause skin
burns. To prevent skin burns, use
work gloves and/or allow heated
parts to cool down before handling.
4. Detaching Quick change chuck
Pull the bottom collar of the Quick change
chuck forward to detach it.
Attaching or removing battery
pack
1. To connect the battery pack:
Insert the battery pack. It snaps into place to
indicate proper connection.
2. To remove the battery pack:
Press the two buttons on the sides of the bat-
tery pack. Slide the battery pack out of the tool
body.
Bottom collar
Top collar
EY6535(EU).book Page 8 Tuesday, March 1, 2005 9:36 AM
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic ey 6535 gqkw at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic ey 6535 gqkw in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info