476028
63
Zoom out
Zoom in
Previous page
1/88
Next page
63
VQT2J52
Setting menus
Signal Condition
You can check the quality and strength of digital broadcast signals.
The quality and strength of the
signal are shown.
Press [WXCH] to select the
channel.
When “Signal Condition” is
displayed in grey and cannot be
selected:
1 Press [EXIT] to exit the screen.
2 Press [WXCH] to select a digital channel. “D” appears on the
unit’s display.
3 Display the Setup menu again (> 62).
Signal Quality
Below 2 (display red):
The signal quality is so poor that there may be interference in the
pictures and sound.
2–5 (display orange):
The signal quality is basically adequate, but brief interference in the
pictures and sound is possible in isolated case.
Over 5 (display green):
Optimum picture and sound quality.
Signal Strength
The display for signal strength is grey. “0” means signal strength 0%,
“10” means signal strength 100%.
If the signal is too strong, the display will change from grey to red.
Reduce the signal amplification at your aerial.
When the signal is weak:
adjust the aerial reception with “DVB Manual Tuning” in the
Setup menu (> 62).
check that the current digital broadcast channel is correctly
broadcasting.
DVB Preferred Language
§1
[For]Italy[and[Spain] The default setting.
§2
[For]Germany[and]Austria[ The default setting.
§3
The language specified as “Original” by the broadcast channel.
Settings for Analogue Channels
[For]Germany[and]Austria[
Press [OK] to show the following setting.
Manual Tuning
You can delete analogue channels and set the analogue channel
details.
To delete a programme position
Press [3, 4, 2, 1] to select a programme position and press the
“Red” button.
This unit does not support SECAM L, L’.
To change the tuning settings for individual programme
position
1 Press [3, 4, 2, 1] to select a programme position and press
[OK].
2 Press [3, 4] to select an item and press [1].
You can make the following two settings by selecting the external
input channel (AV1, AV2, AV3) in step 1.
Video System (Auto/PAL/SECAM)
In order to record properly, make the appropriate settings to match
the connected equipment.
Title Page (Auto/Off)
You can select up to 2 different subtitles and audio tracks to be
used when audio and subtitles digital broadcasts are received.
Select the order of priority.
If the selected language is not available, then the language
included in the broadcast programme is selected.
Multi Audio
Multi Audio ( alternative )
[English]
§1
[German]
§2
[Italian] [French]
[Spanish] [Catalan] [Basque] [Galician]
[Corsican]
[Original]
§3
Subtitles
Subtitles ( alternative )
[English]
§1
[German]
§2
[Italian] [French]
[Spanish] [Catalan] [Basque] [Galician]
[Corsican]
[Original]
§3
Signal Quality 010
Signal Strength 010
DVB Channel
DVB Signal Condition
RETURN
Channel
+
Channel
[CH14] 5 BR3
Manual Tuning
Pos Channel CH Pos Channel CH
Delete
1 ARD 4
2 ZDF
2
3 N3
5
4 HR3
8
5 BR3 10
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
OK
RETURN
SELECT
Pos
Programme position in the table
(You cannot change the programme position.)
Channel
To enter or change the Channel of a TV station
Press [3, 4, 2, 1] to enter station name and press [OK].
If the station name needs a blank space, select the blank
between “Z” and “¢”.
CH
To enter newly available TV stations or change the CH
number of an already tuned TV station
Press [3, 4] or the numbered buttons to enter the CH number
of the desired TV station.
Wait a few moments until the desired TV station has been tuned.
After the desired TV station is tuned, press [OK].
Fine Tuning
To obtain the best tuning condition
Press [3, 4] to adjust the best tuning condition and press [OK].
Press [1] to return to “Auto”.
Video System
To select the video system type
Press [3, 4] to select “PAL” or “SECAM” if the picture lacks
colour, and press [OK].
Auto
This unit automatically distinguishes PAL and SECAM signals.
PAL
For receiving PAL signals.
SECAM
For receiving SECAM signals.
Mono
To select the type of sound to be recorded
Press [3, 4] to select “On” if the stereo sound is distorted due
to inferior reception conditions, or if you want to record the
normal (mono) sound during a stereo or bilingual broadcast, and
press [OK].
Title Page
To enter the Teletext title page for a channel
Entering title page number allows the unit to automatically record
programme and station names.
Press [3, 4] or numbered buttons to enter the number and
press [OK].
To find the correct title page for the station, refer to its Teletext
TV guide.
Note
Pos
Channel
CH
Fine Tuning
Video System
901
4
Auto
Manual
Tuning
ARD
Auto
Mono
Off
Title Page
301
SELECT
DMR-EZ49VEGEC-VQT2J52_eng.book 63 ページ 2010年1月7日 木曜日 午後4時0
63


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic DMR-EZ49V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic DMR-EZ49V in the language / languages: English as an attachment in your email.

The manual is 14,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic DMR-EZ49V

Panasonic DMR-EZ49V User Manual - German - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info