603026

Panasonic DMPBDT100EG Manual

32
Zoom out
Zoom in
Previous page
1/320
Next page
32
VQT2U34
ReferenceReference
Troubleshooting guide
Before requesting service, please perform
the following steps.
The following do not indicate a problem with this unit:
≥ Regular disc rotating sounds.
≥ Image disturbance during search.
≥ Image disturbance when replacing 3D discs.
∫ Unit doesn’t respond to remote
control or front panel buttons.
Press and hold [Í/I] on the main unit for 3 seconds.
– If still unable to turn the unit off, disconnect the AC mains
lead, wait 1 minute, then reconnect the AC mains lead.
∫ Cannot eject disc.
The unit may have a problem.
1 While the unit is off, press and hold [OK], the yellow
button and the blue button on the remote control at the
same time for more than 5 seconds.
– “00 RET” is displayed on the unit’s display.
2 Repeatedly press [1] (right) on the remote control or
[Í/I] on the unit until “06 FTO” is displayed on the unit’s
display.
3 Press [OK] on the remote control or [< OPEN/CLOSE]
on the unit.
To return to the factory preset.
¾
Select “Yes” in “Default Settings” in the Setup menu.
(
>
31)
To return all settings to the factory preset.
¾
Reset the unit as follows:
1 While the unit is off, press and hold [OK], the yellow
button and the blue button on the remote control at the
same time for more than 5 seconds.
– “00 RET” is displayed on the unit’s display.
2 Repeatedly press [1] (right) on the remote control or
[Í/I] on the unit until “08 FIN” is displayed on the unit’s
display.
3 Press and hold [OK] on the remote control or [< OPEN/
CLOSE] on the unit for at least 3 seconds.
This unit is turned off when the input for the
TV is switched.
¾
This is a normal phenomenon when using VIERA Link
(HDAVI Control 4 or later). For details please read the
operating instructions for the TV.
The remote control doesn’t work properly.
¾
The remote control and main unit are using different
codes. If “SET 1”, “SET 2” or “SET 3” is displayed when
a button is pressed on the remote control, change the
code on the remote control. (> 31)
¾
It may be necessary to set the manufacturer code or the
remote control code again after changing the batteries
for the remote control. (> 15)
The TV tuner mode is not displayed when
the TV is switched on.
¾
This phenomenon may occur, depending on the TV
setting, when “Quick Start” is set to “On”.
– Depending on the TV, this phenomenon may be prevented
by reconnecting the HDMI cable to a different HDMI input
terminal or by changing the HDMI auto connection setting.
You have forgotten your ratings password.
You want to cancel the ratings level.
¾
The ratings level returns to the factory preset.
1 While the unit is on, press and hold [OK], the yellow
button and the blue button on the remote control at the
same time for more than 5 seconds.
– “00 RET” is displayed on the unit’s display.
2 Repeatedly press [1] (right) on the remote control or
[Í/I] on the unit until “03 VL” is displayed on the unit’s
display.
3 Press [OK] on the remote control or [< OPEN/CLOSE]
on the unit.
Do you have the latest firmware installed?
Firmware updates may be released to correct operating
irregularities that are discovered with certain movies.
(> 14)
4
Make the following checks.
If the problem remains unresolved, consult
your dealer for instructions.
General operation
(32)
DMP-BDT100EG-VQT2U34.book 32 ページ ２０１０年６月２２日　火曜日　午前１１時０分
… 32 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic DMPBDT100EG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic DMPBDT100EG in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish as an attachment in your email.

The manual is 10,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic DMPBDT100EG

Panasonic DMPBDT100EG User Manual - German, Dutch, Danish, French, Italian - 320 pages

Panasonic DMPBDT100EG User Manual - Polish - 48 pages

Panasonic DMPBDT100EG User Manual - Swedish, Spanish, Spanish - 320 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info