597959
24
Zoom out
Zoom in
Previous page
1/124
Next page
24
Chapter 3 Recording and Playback (continued)
3-2 Basic Procedures
This section describes the basic procedure for shooting and
recording. Before you embark on a shoot, pre-inspect your
system to ensure that it works properly.
* For directions on inspecting your memory card camera-recorder,
see [7-1 Inspections Before Shooting].
Battery Set-up to P2 card Insertion
1 Insert a charged battery pack.
2 Turn on the POWER switch and ensure that more than
four segments of the battery-remaining amount
indication bar are illuminated.
z If the number of illuminated segments is fewer than
five, first check the battery placement. If placement is
not the problem, replace the battery with a fully
charged one.
3 Insert a P2 card and ensure that the P2 CARD
ACCESS LED stays on in orange or green. Then, close
the slide-out door.
When more than one P2 card slot contains a P2 card,
the card in the slot with the lowest number is used first.
However, regardless of slot number, a P2 card inserted
later will not be accessed until the other cards have
been used.
Example:
If all five slots contain P2 cards, the cards are used in
order of slot numbers 12345. However, if the
P2 card in Slot 1 is removed and then re-inserted, the
cards will be used in the following order:
23451.
Note that the recording order is retained even if the power is
turned off. When the power is next turned on, the last card
written before powering-down will be the target card.
<Note>
When “SLOT1” is selected for the menu option P.ON REC
SLOT SEL, recording starts from the P2 card inserted in the
smallest slot number, after the power is turned on.
This option is found in the REC FUNCTION screen on the
SYSTEM SETTING page.
Switch Setting
When a battery and P2 cards are installed, set the switches
as detailed below, before starting to use your AJ-SPC700P.
Setting the switches before shooting and recording
<Notes>
z The USER MAIN button is factory-set to perform the slot
selection function, which selects the target card from
among several P2 cards.
When a new target P2 card is selected, the appropriate
slot number appears on the P2 card remaining amount
indicator in the viewfinder.
For more information about the indications in the
viewfinder, see [4-7-2 Viewfinder Status Indication
Layout].
z SLOT SEL function is enabled during recording; however,
a few seconds are required for switching slots. When the
target P2 card is switched during recording, further
switching to a different P2 card cannot be accepted for
over ten seconds after the first switch.
z The ability to switch to a different target P2 card using the
SLOT SEL function is not available over ten seconds after
recording starts.
z When a Voice Memo is recorded simultaneously with the
video and sound, video and sound recording continues
after switching of the target P2 card using the SLOT SEL
function; however, Voice Memo recording stops.
2
1
2
12345
3
OUTPUT:
CAM/AUTO KNEE ON
AUDIO SELECT
CH 1/CH 2:
AUTO
Iris: Auto
TCG:
F-RUN or
R-RUN
GAIN:
Normally, this should be set to 0 dB. If
conditions are too dark, an
appropriate gain level should be set.
USER MAIN:
This switch is factory-set to
perform slot selection.
#,52%2'PINKUJDQQMࡍ࡯ࠫ㧞㧜㧜㧢ᐕ㧡᦬㧝㧝ᣣޓᧁᦐᣣޓඦ೨㧥ᤨ㧠㧡ಽ
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic AJ-SPC 700P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic AJ-SPC 700P in the language / languages: English as an attachment in your email.

The manual is 6,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info