597959
23
Zoom out
Zoom in
Previous page
1/124
Next page
23
3
Chapter 3 Recording and Playback (continued)
Removing P2 Cards
1 While pressing down the slide lock button, move the
slide-out door to the left.
The door opens.
2 Tilt down the EJECT button.
3 Then, depress the EJECT button to release the P2 card
so that you can remove it.
<Notes>
z When a P2 card is being accessed or it is being
recognised after insertion (P2 CARD ACCESS LED blinks
in orange), do not remove the P2 card.
If your AJ-SPC700P is not set to turn on the P2 CARD
ACCESS LED, before removing the card ensure that pre-
recording and/or voice memo recording have finished (the
P-REC indication has stopped blinking and the V mark or
VOICE REC indication on the viewfinder screen has
turned off) after stopping recording or playback.
z If a P2 card being accessed is removed, the viewfinder
displays “TURN POWER OFF” and the AJ-SPC700P
gives a warning using an alarm and the WARNING LED.
In addition, all P2 CARD ACCESS LEDs blink rapidly in
green. If this is the case, turn the power off. For more
information on warning indications, see [7-3 Warning
System].
z If a P2 card is removed while being accessed, clips on it
may become irregular although the data will not be
corrupted. Check the clips and restore them if required.
For more information about how to restore clips, see [6-9
Restoring Clips].
z If a P2 card being formatted is removed, it may be not be
formatted properly. In this case, the viewfinder displays
“TURN POWER OFF”. If this message appears, turn off
the power, then restart the AJ-SPC700P to reformat the
card.
z If a P2 card is inserted while another P2 card is being
played back, the inserted P2 card is not recognised and
the P2 CARD ACCESS LED for that card does not come
on. Card recognition starts when the playback ends.
<For Your Information>
The P2 CARD ACCESS LEDs may be set to stay off using
the menu option ACCESS LED. This option can be found on
the <SYSTEM MODE> screen, which is accessible from the
SYSTEM SETTING page.
To Prevent Accidental Erasure of P2 Card Content
To prevent the content of a P2 card being accidentally
erased, position the write-protect switch on the P2 card at
[Protect].
<Note>
Write-protect switchover can be performed while the card is
being accessed (during recording or playback), but does not
take effect until access to the card ceases.
* The mode check indication is shown in the viewfinder. For more
information, see [4-7-2 Viewfinder Status Indication Layout].
Depress the tilted-down
EJECT button to release
the P2 card.
Tilt down the EJECT
button.
P2 CARD ACCESS LED and status of P2 cards
P2 CARD
ACCESS LED
MODE CHECK
indication*
Status of P2 Card
Stays on in green ACTIVE
Writing and reading
enabled
Stays on in
orange
ACTIVE
Writing and reading
enabled. The card is
recordable (loop recording
also enabled).
Stays on in
orange or green
ACTIVE !
Writing and reading
enabled. However, some
clips recorded on the P2
card may not be able to be
read successfully.
Blinks in orange ACCESSING
Writing or reading being
performed.
Quickly blinks in
green
INFO READING
The P2 card is being
recognised.
Blinks in green
FULL
The P2 card has no free
space. Only reading is
enabled.
PROTECTED
The write-protect switch on
the P2 card is positioned at
[PROTECT]. Only reading
is enabled.
Stays off
NOT
SUPPORTED
The card is not supported
by your AJ-SPC700P.
Replace the card.
FORMAT ERROR
The P2 card is not properly
formatted. Reformat the
card.
NO CARD No P2 card is inserted.
Protect
Write-protect switch
#,52%2'PINKUJDQQMࡍ࡯ࠫ㧞㧜㧜㧢ᐕ㧡᦬㧝㧝ᣣޓᧁᦐᣣޓඦ೨㧥ᤨ㧠㧡ಽ
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic AJ-SPC 700P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic AJ-SPC 700P in the language / languages: English as an attachment in your email.

The manual is 6,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info