597941
122
Zoom out
Zoom in
Previous page
1/138
Next page
122
Displays
Something is wrong with
the time code display.
The time code display may not register a regular count if a tape is
played in the reverse slow mode. This is normal.
The remaining tape display
differs from the actual
amount of tape remaining.
The remaining tape is not displayed accurately if you shoot
continuously for periods of less than 30 seconds.
The display may show 2 to 3 minutes less than the actual time
remaining on the tape.
Playback
Cannot play even when I
press the play button.
Make sure the MCR/VCR lamp is on (press the mode button).
No kind of playback operation can be performed unless this lamp is
on.
P 63, 64
Cannot play back P2 cards
or tapes.
Make sure the MEDIA switch is in the correct position.
If not, set it to the P2 or TAPE position.
P 63, 64
Mosaic-like noise appears
when I cue or review a tape.
This noise is inherent to digital video technology. This is normal.
Images do not appear on
the television even though
I have connected the
camera-recorder properly.
Make sure the input selector on your television is set to video input.
Read the television’s instructions carefully and select the correct
video input connector for the camera-recorder.
When a component video cable is connected, video signals are not
output from the VIDEO OUT and S-VIDEO OUT connectors.
P 80
The playback images are
not displayed clearly.
The camera-recorder’s heads may be dirty.
Images will not be displayed clearly if the heads are dirty.
Cannot hear any sound
from the camera-recorder’s
speaker.
You may have turned down the camera-recorder’s volume control
too far.
Adjust the volume level using the AUDIO MON/ VAR button+.
P 76
I can hear two sets of
sound.
You may have selected “MIX” as the 32K(12bit) AUDIO setting in
the PLAYBACK FUNCTION screen.
P 110
If you perform audio dubbing on a tape that was recorded with 32K
(12bit) selected as the AUDIO REC setting in the RECORDING
SETUP screen, you will hear the sound heard during recording
and that of the audio dubbing. You can also listen to each sound
separately.
P 107
When I performed audio
dubbing, the original sound
was erased.
If you perform audio dubbing on a tape that was recorded with 48K
(16bit) selected as the AUDIO REC setting in the RECORDING
SETUP screen, you will hear the sound heard during recording and
that of the audio dubbing. To leave the original sound intact, make
sure that 32K (12bit) is selected when you shoot.
P 107
Cannot perform hot swap
playback.
This unit does not support hot swap playback.
To replace one card with another during dubbing, stop the dubbing
first, and upon completing the replacement, resume it.
P 88
Before calling for service (continued)
122


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic AG-HVX 200AP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic AG-HVX 200AP in the language / languages: English as an attachment in your email.

The manual is 16,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info