597937
143
Zoom out
Zoom in
Previous page
1/166
Next page
143
Chapter 8 Connecting to External Devices
5
Select OPERATION FORMAT (HDD) in the
menu and use a cursor button and the SET
button to select YES.
Select YES in the confirmation message that
appears again to start hard disk drive formatting.
Handled as a “TYPE S” hard disk drive after
formatting.
NOTE
All data on a hard disk drive is deleted when the disk is
formatted. It is not possible to select part of a partition
to delete.
Writing to hard disk drive
1
Switch to the USB host mode.
For details, refer to [Switching to USB Host Mode]
(page 140).
2
Connect a hard disk drive via USB.
If the hard disk drive has not been formatted by
the camera, format it according to the instructions
provided in [Formatting Hard Disks] (page 142).
3
Insert a P2 card.
4
Press the THUMBNAIL button to open the
thumbnail screen.
5
Press the THUMBNAIL button and select HDD
EXPORT from the thumbnail menu and
specify the slot of the P2 card with the data you
want to write to the hard disk drive.
6
Select YES.
This starts the write process.
A progress bar appears during the write process.
To interrupt writing, press the SET button.
Selecting YES in the cancel confirmation that
appears will stop the write process.
COPY COMPLETED! announces the end of the
write process.
NOTE
To turn off the verify phase in a write operation, select
HDD SETUP in the thumbnail menu and set VERIFY
to OFF. This speeds up the write time but does not
verify the written data.
Selecting ALL SLOT writes the data on all inserted P2
cards inserted in the camera to the hard disk drive.
NOTE
A TYPE S hard disk drive can write data in card units. Up
to 23 P2 cards can be saved to a hard disk drive.
The P2 card data recorded on a hard disk drive are
recognized as separate drives.
To write P2 cards with bad clips, it is a good idea to repair
these clips before writing them to a hard disk drive.
Ending a recording during the verify phase will end writing
of data from the P2 card to the hard disk drive.
Writing back data to P2 cards
This allows you to select a clip from the hard disk drive and
write it back to a P2 card.
1
Switch to the USB host mode.
For details, refer to [Switching to USB Host Mode]
(page 140).
2
Connect a hard disk drive via USB.
3
Insert the P2 card to which data will be written
back to.
4
Press the THUMBNAIL button, select HDD
EXPLORE from the thumbnail menu, move to
the partition with the data that will be read and
press the SET button.
5
Select the clip to be written to the P2 card from
the thumbnail on the hard disk drive.
6
Press the THUMBNAIL button, select
OPERATION IMPORT SELECTED CLIPS
from the thumbnail menu and select the slot of
the P2 card to write the data to.
7
Select YES.
This starts the data write to the P2 card.
When the write process ends, “COPY
COMPLETED!” appears.
NOTE
When clips are selected for writing, verify is not performed.
143


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic AG-HPX 300P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic AG-HPX 300P in the language / languages: English as an attachment in your email.

The manual is 12,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info