597931
76
Zoom out
Zoom in
Previous page
1/82
Next page
76
Before calling for service (cont.)
Playback (sound)
Other
I can’t hear any sound
from the camera-
recorder’s speaker.
Have you turned down the camera-recorder’s volume control too
far?
In the VCR mode, adjust the volume level using the multi dial.
P44
I can hear two sets of
sound.
Have you selected “MIX” as the 32K (12bit) AUDIO item setting on
the PLAYBACK FUNCTION screen?
If you perform audio dubbing on a tape that was recorded with “32K
(12bit)” selected as the AUDIO REC item setting on the RECORD-
ING SETUP screen, you will hear the sound heard during recording
and that of the audio dubbing.
P67
P69
When I performed audio
dubbing on an existing
recording, the original
sound was erased.
If you perform audio dubbing on a tape that was recorded with “48K
(16bit)” selected as the AUDIO REC item setting on the RECORD-
ING SETUP screen, you will erase the original sound on the tape.
To leave the original sound intact, make sure that “32K (12bit)” is
selected as the item setting when you shoot the original recording.
P69
I can’t remove the cas-
sette tape.
Is power still being supplied to the camera-recorder? (Is the power
from the AC adapter and battery supplied properly?)
So long as the power is supplied, you can remove the cassette
even if the POWER lever is at the OFF position.
–––
I can remove the cassette
but I can’t perform any
other operations.
Has condensation formed?
If it forms, the only operation you can perform is to remove the cas-
sette. Wait until the condensation has dried out.
If the cassette cover is closed immediately after sliding the EJECT
switch to open the cassette cover, you may no longer be able to
perform any operations other than eject. If you did this, slide the
EJECT switch again to open the cassette cover, check that the cas-
sette mechanism has finished ejecting the cassette, and then close
the cassette cover.
P77
–––
The remote control unit
does not work.
Has the button battery in the remote control unit run out?
If the remote control fails to work even when it is operated near the
camera-recorder’s remote control sensor, it means that the button
battery has run out. Replace it with a new one.
Is the remote control setting the same for the remote control unit
and the camera-recorder?
If the REMOTE item setting does not correspond between the two
units, the remote control unit will not work.
P19
P19, 72
I hear a rattling sound
when I tilt the camera-
recorder back and forth.
There are some parts in the structure of the camera unit that make
a rattling sound in the VCR mode or when the POWER lever is at
the OFF position. This is not a sign that something is broken.
–––
76


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic AG-DVC 60p at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic AG-DVC 60p in the language / languages: English as an attachment in your email.

The manual is 2,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info