597925
50
Zoom out
Zoom in
Previous page
1/110
Next page
50
* The COUNT value is indicated as a 4-digit number.
The COUNT value is incremented each time a new
clip is shot when clip metadata has been loaded
and the recording method has been set to [TYPE2].
The COUNT value can be reset with the following
method. Press the <MENU> button, select [META
DATA]
[CLIP COUNTER RST]
[YES], and push
the OPERATION lever to reset the COUNT value to 1.
Using the counter
Counter display
You can display a counter that indicates how much
time has elapsed during shooting or playback.
1
Press the <COUNTER> button.
Each time you press the button, the display
changes as follows. (Page 75)
[0:00.00] (<CAMERA> mode only)
Counter value display. Displayed when [TOTAL]*
is selected with the [REC COUNTER] item on
the setup menu [DISPLAY SETUP] screen.
[CLIP 0:00.00]
Displayed when [CLIP]* is selected with the
[REC COUNTER] item on the setup menu
[DISPLAY SETUP] screen.
Values are automatically reset when shooting
is started, and counter values are displayed
for each individual clip.
* The count is not displayed in <PB> mode.
[TC 12:34:56.01]
Time code display (Displays the frame digits
in 24 frames in PH1080/24P and PH720/24P
modes. In 480i/24P mode, the frame digits are
converted into 30 frames.)
[UB 12 34 56 78]
User information
No display:
Data is not displayed.
To reset the counter value, press the <RESET/
TC SET> button while the counter value is
being displayed.
TC preset mode
Synchronizes the initial time code value during
multi-camera shooting. (Hereafter, the camera used
for synchronization is described as the MASTER
and the camera being synchronized is described
as the SLAVE.)
1
Connect the TC PRESET IN/OUT terminals
(<VIDEO OUT> terminals) on the two devices
with a pin cable, and turn on the power.
MASTER settings
2
Check that the MASTER camera is set to
the <CAMERA> mode, and set the [EXT
TC LINK] item on the setup menu [TC/UB
SETUP] screen to [MASTER].
[OUTPUTTING LTC SIGNAL] is displayed on
the screen, and the time code is output from the
TC PRESET IN/OUT terminal (<VIDEO OUT>
terminal).
Select the same recording format for the
MASTER and SLAVE cameras, and set the
[TCG] item on the [TC/UB SETUP] screen to
[FREE RUN].
To cancel the time code output, press the
<MENU> button.
SLAVE settings
3
Set the [EXT TC LINK] item on the setup
menu [TC/UB SETUP] screen to [SLAVE].
4
Press the <COUNTER>-<RESET/TC SET>
button. TCG values will be preset to the TC
values input from the MASTER.
The menu screen is closed and [TC LINK OK]
is displayed in the center of the screen.
If the TC values cannot be set correctly, [LINK
NG] will be displayed.
If the SLAVE camera is set to 24P, set the [TC
MODE] item of the MASTER camera to [NDF].
To cancel the [SLAVE] mode, press the
<MENU> button.
50


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic AG-AC160AEJ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic AG-AC160AEJ in the language / languages: English as an attachment in your email.

The manual is 12,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info