779808
16
Zoom out
Zoom in
Previous page
1/32
Next page
You MUST STOP using the machine if any of the following occur.
The engine speed changes with no control.
In case of misfire
In case of high vibration.
If you are not familiar with this type of machine you should seek advice and guidance from your
dealer.
DO NOT attempt to lift or move the machine while the engine is running.
5.1. Machine use.
5.1.1. Position the machine in such a way that it cannot move during use, maintenance, cleaning,
adjustment, assembly of accessories or spare parts, as well as under storage. 5.1.2. DO NOT force
the machine. Use the correct machine for your application. The correct machine will do the job better
and safer at the rate for which it is designed.
5.1.3. DO NOT change the engine governor settings or over-speed the engine. The governor
controls the maximum safe operating speed of the engine.
5.1.4. DO NOT run the engine at a high speed when you are not using it.
5.1.5. DO NOT put hands or feet near the high pressure jet. Failure to observe these safety
instructions could result in serious injury.
5.1.6. Use only attachments and accessories approved by the manufacturer. Failure to do so can
result in personal injury, and may invalidate any warranty.
5.1.7. DO NOT allow persons unfamiliar with the machine or these instructions to operate it. This
machine is extremely is dangerous in the hands of untrained users.
5.2. Work area.
5.2.1. Thoroughly inspect the area to be worked, keep the working area clean and free of debris to
prevent tripping. Operate on a flat level ground.
5.2.2. NEVER place any part of your body where it would be in danger if movement should occur
during assembly, installation, and operation, maintenance, repairing or moving.
5.2.3. Keep all bystanders, children, and pets at least 23m (75 feet) away. If you are approached,
stop the unit immediately.
5.2.4. The operator or user is responsible for preventing accidents or hazards occurring to other
people, their property, and themselves.
5.2.5. Start the engine carefully according to instructions.
5.2.6. Before starting the pressure washer, make sure that the area to pressure washed is free of all
obstacles.
5.2.7. Whenever you leave the operating position you MUST always shut down the engine,
disconnect spark plug HT lead, keeping them away from the spark plugs to prevent accidental
starting, and wait for all moving parts to come to a complete stop.
5.2.8. ALWAYS stop the engine before moving the machine.
5.2.9. NEVER cover the machine while the exhaust is still hot.
5.2.10. NEVER operate the machine on slopes.
5.2.11. Move the machine at least 3m away from the refueling point before starting engine.
5.2.12. Inspect that all nuts and bolts are tight and well connected to ensure the safety and
5. USING THE MACHINE
Page 16
First edition - April 2017
The water must be turned on prior to starting the washer, pull the spray trigger to ensure water is
moving the through the lines and out the nozzle without any leaks before starting the unit. Failure to
do this will result in damage to the seals which will not be covered under warranty
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for P1PE PGP200PWA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of P1PE PGP200PWA in the language / languages: English as an attachment in your email.

The manual is 9.45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info