606572

Oxford OF772 HotGrips Manual

6
Zoom out
Zoom in
Previous page
1/40
Next page
71cm
30cm
71cm
15cm
Panel
230cm
LED light
5. When the wiring is in position on the motorcycle, we strongly recommend that all connectors are
protected with either electrical insulation tape, waterproof sealing tape or heat shrink tubing
(be careful not to damage the cable when tting heat shrink).
6. Both the negative and the positive battery connections are tted with a ring terminal. This will allow
them to be bolted to the battery terminals. It is the easiest option to connect the positive (+ Red wire)
straight to the positive (+) battery terminal so that the grips receive sufcient voltage from the vehicles
charging system.
7. The negative or earth (Black wire) should be connected to the negative (-) battery terminal.
8. If the switch is connected to a switched ignition supply feed, please ensure that the wiring
harness is connected to main ignition cabling which can take the extra load of up to 3 amps.
Problems are commonly found to be caused when connections are made to horn or any lighting
circuits.
Typical problems experienced could be:
- The switch may not come on
- Fuses failing in the fuse box
- Overheating of wires on the bike
- Indicators or lighting malfunctioning
If unsure, please contact your local dealer for advice before tting these Hotgrips.
Refer to the wiring diagram below.
I: Usage guidelines
1. Once tted the OXFORD HotGrips are designed for keeping gloved hands at a comfortable and warm
temperature. Small changes to the ambient temperature will affect the temperature of the HotGrips
and it is necessary to adjust temperature as appropriate. For simplicity and reliability, there are 2
possible power settings.
In the LOW position the power is restricted to 25% and would commonly be used when the ambient
temperature is between 10° to 17° C.
In the HIGH position the power is at 100% and would be used when temperatures are between 0°
and 9°. These ambient temperatures are given as a guide only and varies depending on the rider and
what type of gloves are worn.
If the grips are too hot please ensure the heat controller is turned to the LOW position or even switch
it OFF if necessary.
2. If connected directly to the battery, please ensure that you remember to switch off the HOTGRIPS
before leaving the vehicle. The optional LED light should remind you that it is switched on.
Unfortunately Oxford Products cannot accept any responsibility for attened batteries.
6 Oxford Scooter HotGrips Instructions 10/12
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oxford OF772 HotGrips at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oxford OF772 HotGrips in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info