Manual Oxford OF772 HotGrips (page 5 of 40) (English, German, French, Italian, Spanish)

606572

Zoom out

Zoom in

1/40

3. Clutch side HotGrips:

• Apply plenty of glue along the length and around the diameter of the handle bar where the grip

will nally sit.

• Push the grip into place ensuring that the HotGrips are positioned correctly so it does not foul the

clutch operation.

4. Throttle side HotGrips:

• If the grip is a very tight t over the throttle slider, then it is advisable to apply plenty of glue on

the actual nylon throttle slider on the inner most ange and less along the length of the throttle

slider. This is to ensure that the grip and glue do not set too early and half way up the throttle

slider. We would also recommend to apply a ring of glue around the outer end of the throttle slider

as some of this will naturally be drawn up the length of the throttle slider tube.

If however the grip slides easily over the throttle slider then we would recommend using plenty

of glue around the whole circumference of the throttle slider to ensure a safe and secure tment.

5. Be sure to act immediately to wipe away any excess glue with a dry cloth.

6. Allow the glue to dry for at least 24 hours before using. Ensure that the grips are rmly xed in place

before use. Do not use if the grip moves and seek advice immediately.

H: Wiring Harness Installation

1. Find a suitable location to panel mount the switch and then take the wiring back to the battery to

ensure it easily reaches. Then unscrew the panel before drilling a hole of approximately 20mm.

In this kit, we provide a 20mm drill bit for making the hole. It will form a hole in most plastic panels.

When drilling, choose a slow drill speed and slowly create the hole. Remember to wear appropriate

safety goggles and clothing.

If you prefer, most motorcycle dealers will be happy to t these Hotgrips for you.

Put the whole wiring loom through the 20mm hole and feed the wiring along the scooter chassis until

the ring leads reach the battery. Push the switch into the hole and ensure it has popped into position

and is retained securely in the panel. Ensure that the waterproof switch cover is wrapped under the

switch and is therefore sealing against the body panel.

2. Remember to install the switch in a suitable position ensuring the wiring harness will reach the wires

from the grips without strain.

3. The loom is designed for ease of tting. There are only 2 wires that need attaching to the scooter’s

existing wiring system. All other connections are through the multi pin block connectors and cannot

be tted the wrong way.

4. A panel mount LED has been included in the wiring loom which can be tted near to the switch if

required. To t this, drill a 6.5 mm diameter hole and push the LED light from the inside of the panel

and it will pop into place.

Oxford Scooter HotGrips Instructions 10/12 5

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Oxford OF772 HotGrips in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Oxford OF772 HotGrips Manual

Product: