606568
5
Zoom out
Zoom in
Previous page
1/42
Next page
3. Clutch side HotGrips:
Apply plenty of glue along the length and around the diameter of the handle bar where the grip
will nally sit.
Push the grip into place ensuring that the HotGrips are positioned correctly so it does not foul the
clutch operation.
4. Throttle side HotGrips:
If the grip is a very tight fi t over the throttle slider, then it is advisable to apply plenty of glue on
the actual nylon throttle slider on the inner most fl ange and less along the length of the throttle
slider. This is to ensure that the grip and glue do not set too early and half way up the throttle
slider. We would also recommend to apply a ring of glue around the outer end of the throttle slider
as some of this will naturally be drawn up the length of the throttle slider tube.
If however the grip slides easily over the throttle slider then we would recommend using plenty
of glue around the whole circumference of the throttle slider to ensure a safe and secure fi tment.
5. Be sure to act immediately to wipe away any excess glue with a dry cloth.
6. Allow the glue to dry for at least 24 hours before using. Ensure that the grips are fi rmly fi xed in place
before use. Do not use if the grip moves and seek advice immediately.
H: Wiring Harness Installation
1. Find a suitable location to mount the switch and then take the wiring back to the battery.
2. Install the switch in a suitable position ensuring the wires from the grips reach without strain.
3. The switch may be mounted on a fl at panel using the self adhesive mounting foam pad. It may also
be mounted on the metal bracket supplied (if the bracket is suitable for the vehicle). Please fi t the
foam pad between the bracket and switch to reduce vibrations. The bracket may also be bent to a
different shape if required.
4. On many bikes it is possible to fi t the bracket to the clutch clamp as shown below using the longer
bolts provided.
5. The loom is designed for ease of fi tting. There are only 2 wires that need attaching to the motorcycles
existing wiring system. All other connections are through the multi pin block connectors and cannot
be fi tted the wrong way. Ensure that the round din plug connector is carefully assembled and that the
arrows on both halves of the casing are lines up before pushing together. If care is not taken it might
be possible to damage the small connecting pins.
Install the HotGrip Switch
as shown using the optional
bracket (OF91)
Oxford Hotgrips instructions v.7 switch - 10/12/08 4
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oxford OF696 HotGrips at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oxford OF696 HotGrips in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Oxford OF696 HotGrips

Oxford OF696 HotGrips Usermanual and installation guide - Dutch - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info