759842
20
Zoom out
Zoom in
Previous page
1/38
Next page
© Outdoor Life Group Nederland B.V. - v16.1 -18-
www.outdoorlifeproducts.com
Leggen EPDM-dakbedekking
Hoeken
6 hoeken vouwen tot een puntzak
7 hoeken niet knippen maar vouwen
8 hoeken plat op de dakrand vouwen
Hemelwaterafvoer
1/8 Plaats de EPDM folie op het dakvlak volgens de
verwerkingsvoorschriften.
9 Bepaal de exacte positie van de afvoer, en knip
daar vervolgens een gat in de EPDM van ± Ø 3
cm.
10 Duw de afvoer in het gat tot de ronde plakplaat
netjes op de ondergrond ligt.
11 Teken de omtrek van de ronde plakplaat af met
bijv. een krijtje.
Trek de afvoer uit het gat.
12 Breng vervolgens een rups kit aan op de vol-
gende plaatsen:
a Net binnen de afgetekende lijn.
b Rond het uitgeknipte gat.
c Vervolgens van buiten naar binnen met een
tussenafstand van ± 3 cm.
13 Duw de afvoer in het gat en druk vervolgens de
ronde plakplaat stevig aan.
Controle: De kit moet aan de rand goed zichtbaar
zijn, dan is de afvoer goed ingeplakt!!
Ecken
6 Die Ecken falten wie eine Spitztüte
7 Die Ecken nicht schneiden, aber falten.
8 Die Ecken ach auf den Dachrand falten.
Fallrohrverbindung
1/8 Verlegen Sie die EPDM-Folie auf dem Un-
tergrund, wie in den Verlegehinweisen beschrie-
ben.
9 Bestimmen Sie die Position des Fallrohrs und
schneiden Sie ein Loch in die EPDM-Folie von ±
Ø 3 cm
10 Drücken Sie das Fallrohr in das Loch, bis die
runde Gummiabdichtung ach auf dem Dach
liegt.
11 Markieren Sie den Umkreis der runden Fallrohr-
gummiabdichtung z.B. mit Kreide.
Ziehen Sie das Fallrohr aus dem Loch
12 Danach platzieren Sie den Kitt an folgenden
Stellen:
a In dem markierten Umkreis
b Rund um das ausgeschnittene Loch
c Danach von außen nach innen zwei Kreise mit
einem Abstand von 3 cm
13 Setzen Sie das Fallrohr in das Loch und drücken
Sie danach die runde Gummiabdichtung fest an.
Prüfung: ist der Kitt am Rand deutlich sichtbar, dann
ist das Fallrohr einwandfrei verklebt.
Corners
6 The corners have to be fold as a cone.
7 Do not cut the corners, only fold them.
8 Fold the corners at on the edge of the roof.
Drain Pipe
1/8 Place the EPDM rubber on the roof according to
the instructions.
9 Determine the exact position of the drain pipe
and cut a hole in the EPDM rubber of ± Ø 3
centimeter.
10 Put the drain pipe into the hole until the rubber
circle lies at on the surface.
11 Circumscribe the rubber circle with for example a
piece of chalk.
Remove the drain pipe out of the hole.
12 After this you glue the following parts:
a Just inside the marked line
b Around the hole
c From outside to inside with a space of 3 centi-
meter in between.
13 Put the drain pipe into the hole and push the rub-
ber circle on the roof
pipe has been glued well!
5 86
10
7
119 12
D GBNL
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Outdoor Life Beuk at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Outdoor Life Beuk in the language / languages: All languages as an attachment in your email.

The manual is 4,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info